Lenovo 6241 Installation And Service Manual Download

Page: 167 / 1990

For the location of the LEDs on the modules in the rear of the server, see “Half-length I/O book LEDs” on
page 156 , “Full-length I/O book LEDs” on page 157, “Standard I/O book LEDs” on page 157, and “Power-
supply LEDs” on page 158.

Storage book LEDs

Use this information to determine the location of the LEDs on the storage book.

The following illustration shows the location of the LEDs on the storage book.

Storage book

Reset
button

Power
button\
LED

Locate
button\
LED

Check
log LED

System
error LED

PCIe slot 11
error LED

PCIe slot 12
error LED

Board
error LED

Drive activity
LED (green)

Drive status
LED (yellow)

Chapter 4

Troubleshooting

153

Summary of Contents for 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands

Lenovo 6241, Installation And Service Manual

Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands