Lenovo 6241 Installation And Service Manual Download

Page: 127 / 1990

SAS signal
cable connector

Input power
cable connector

To install the 4x2.5-inch hot-swap drive backplane, complete the following steps:

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 44.

Step 2. Turn off the server (see “Turning off the server” on page 40) and all attached peripheral devices.

Disconnect all power cords; then, disconnect all external cables from the server.

Step 3. Remove the storage book from the server (see “Removing the storage book” on page 273).

Step 4. If a backplane filler panel is installed in the backplane bay in which you are installing the backplane,

remove the backplane filler panel.

Step 5. Insert the backplane tabs into the slots on the left side of the backplane cage and rotate the drive

backplane assembly forward until the backplane locks in place in the retention latch.

Chapter 2

Installing optional devices

113

Summary of Contents for 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands

Lenovo 6241, Installation And Service Manual

Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands