Lenovo 6241 Installation And Service Manual Download

Page: 125 / 1990

Lockbar

USB
Hypervisor
key

Air baffle

Standard I/O book

If you have other devices to install or remove, do so now. Otherwise, go to “Completing the installation” on
page 117.

Installing the drive backplanes

This information provides instructions on how to install the drive backplanes in the server.

The following topics provide instructions on how to install the supported drive backplanes in the server.

Installing the 8x1.8-inch hot-swap drive backplane assembly

This information provides instructions on how to install the 8x1.8-inch drive backplane in the server.

Notes:

• The SAS/SATA adapter that you install in the server to control the backplane must be capable of

supporting two internal, 4-lane SAS/SATA signal connectors.

• The server must have a minimum of two compute books with microprocessors and memory installed to

support the controller, backplane, and drives.

• When you install a 8x1.8-inch drive backplane assembly, the drive IDs that are indicated on the server

front bezel will no longer be valid. Use the drive labels that come with the backplane to renumber the drive
IDs on the bezel.

• For more information about drive IDs, see “Drive IDs” on page 67. For more information about the

supported drive backplane configurations, see “Supported drive backplane configurations” on page 69.

Chapter 2

Installing optional devices

111

Summary of Contents for 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands

Lenovo 6241, Installation And Service Manual

Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands