Lenovo 6241 Installation And Service Manual Download | Manualshive

Page: 83 / 1990

background image

Supported drive backplane configurations

This information describes the supported drive backplane configurations for the server.

Notes:

1. When mixing drive backplane configurations, you must install all 1.8-inch SSD drive backplanes above

all 2.5-inch drive backplanes.

2. When you mix drive backplane configurations, IMM renumbers the drive bay IDs automatically.

3. For more information about installing drives, see “Installing drives” on page 66.

The following illustrations show the hot-swap drive backplanes that the server supports.

4x2.5-inch NVMe PCIe Gen3 solid state drive backplane rear view:

This drive backplane can support up

to four 2.5-inch NVMe PCIe solid state drives. The backplane signal cable is attached to the NVMe PCIe
Gen3 solid state drive extender adapter. Each NVMe PCIe Gen3 solid state drive extender adapter supports
two NVMe PCIe solid state drives.

Port 0

Port 1

Port 2

Port 3

Power connector

4x2.5-inch SAS Gen3 12 Gb drive backplane rear view:

This drive backplane can support up to four 2.5-

inch SAS hard disk drives or four 2.5-inch SATA solid state drives. The backplane power and configuration
signals will be supplied from the standard I/O book using cables.

SAS signal
cable connector

Input power
cable connector

.

Installing optional devices

69

«
...
81
82
83
84
85
...
»

Summary of Contents for 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6241

imagePRESS Server G200

Brand: Canon Pages: 82

Brand: Canon Pages: 88

Brand: Logicbus Pages: 8

D-811_002-NXS-SAG

Brand: NOMACHINE Pages: 19

Brand: Axis Pages: 10

Brand: Data-Tronix Pages: 29

Brand: Data-Tronix Pages: 30

Brand: Epson Pages: 28

EpsonNet 802.11b

Brand: Epson Pages: 30

Stylus C80WN - Ink Jet Printer

Brand: Epson Pages: 1

Brand: Epson Pages: 258

Brand: Epson Pages: 280

PRIMEQUEST 3800E

Brand: Fujitsu Pages: 38

Brand: Fujitsu Pages: 36

Primergy BX2560 M1

Brand: Fujitsu Pages: 68

PRIMEQUEST 3000 Series

Brand: Fujitsu Pages: 44

Brand: Fujitsu Pages: 56

PRIMEQUEST 2800B3

Brand: Fujitsu Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands