Lenovo 6241 Installation And Service Manual Download | Manualshive

Page: 124 / 1990

background image

Filler
panel

Spacer

900-watt ac
power supply

Power supply
release tab

Spacer
release tab

2. Grasp the handle on the rear of the power supply and slide the power supply forward into

the power-supply bay (next to the spacer) until it clicks into place. Make sure that the
power supply connects firmly into the power-supply connector.

3. Go to Step 5 step 4 on page 110.

Step 5. Route the power cord through the cable hook-and-loop on the rear of the server so that it does not

accidentally become unplugged.

Step 6. Connect the power cord for the new power supply to the power-cord connector on the power

supply.

Step 7. Connect the other end of the power cord to a properly grounded electrical outlet.

Step 8. Make sure that the ac power LED on the power supply is lit, indicating that sufficient power is being

supplied to the power supply through the power cord. During normal operation, both the ac and the
dc power LEDs are lit. For any other combination of LEDs, see “Power-supply LEDs” on page 158.
Make sure that no error LEDs are lit.

Step 9. Restart the server. Confirm that it starts correctly and recognizes the newly installed device, and

make sure that no error LEDs are lit.

Installing a USB embedded hypervisor flash device

Use this information for instructions on how to install a USB hypervisor flash device.

To install a hypervisor flash device, complete the following steps:

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 44.

Step 2. Turn off the server (see “Turning off the server” on page 40) and all attached peripheral devices.

Disconnect all power cords; then, disconnect all external cables from the server.

Step 3. Remove the standard I/O book (see “Removing the standard I/O book” on page 224).

Step 4. Locate the USB flash device (hypervisor) connector on the standard I/O book board (see “Standard

I/O book” on page 31 for the location of the connector).

Step 5. Make sure that the lockbar on the USB (hypervisor) connector is in the unlock position (down).

Step 6. Align the USB flash device with the connector on the standard I/O book board and push it into the

connector until it is firmly seated.

Step 7. Slide the lockbar up to the locked position until the lockbar is seated firmly.

110

System x3850 X6 and x3950 X6 Installation and Service Guide

«
...
122
123
124
125
126
...
»

Summary of Contents for 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6241

Z10 BUISNESS CLASS Z10 BC

Brand: IBM Pages: 67

x3450 - System - 7948

Brand: IBM Pages: 2

BladeCenter PN41

Brand: IBM Pages: 88

Brand: KYLAND Pages: 30

NOP1840 PEP-Box

Brand: Newtec Pages: 96

Brand: Xyplex Pages: 58

Brand: TYANO Pages: 68

Brand: Conceptronic Pages: 127

Brand: HIKVISION Pages: 13

ANR-C62-N1 Series

Brand: Acrosser Technology Pages: 57

301269U - Ethernet Disk Mini Home Edition 500 GB Network Attached Storage Hard...

Brand: LaCie Pages: 74

ApplianceStor 75

Brand: Rasilient Pages: 24

Brand: IBM Pages: 76

xSeries 342 2RX

Brand: IBM Pages: 158

StorCenter Pro NAS 200rL

Brand: Iomega Pages: 2

Brand: National Instruments Pages: 4

Brand: Spectra Pages: 184

G4-Apex-ENT-80T

Brand: Viavi Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands