manualshive.com logo in svg

Lenovo 3000K, Hardware Maintenance Manual, Page: 30 / 49

Share
Download
Lenovo 3000K Hardware Maintenance Manual Download Page 30

Hardware Maintenance Manual

28      

Replacing hardware

7

Attention

Do not remove the computer cover or attempt any repair before 
reading the “Safety information” . These precautions and guidelines 
will help you work safely. 

Note

Use only parts provided by Lenovo.

Removing the computer cover 

Important

Turn off the computer and wait 3 to 5 minutes to let the computer 
cool before removing the computer cover.

To remove the computer cover: 

1.  Remove any media (diskettes, CDs, or tapes) from the drives, shut down 

your operating system, turn off all attached devices, and the computer. 

2.  Unplug all power cords from electrical outlets. 
3.  Disconnect all cables attached to the computer. This includes power 

cords, input/output (I/O) cables, and any other cables that are 
connected to the computer. 

4.  Remove any locking devices that secure the computer cover. 
5.  Pull down the switch at the rear of the chassis and slide the computer 

cover to the rear to remove. 

Summary of Contents for 3000K


















































Reviews:

No comments