manualshive.com logo in svg

Lenovo 10AS, User Manual, Page: 62 / 148

Share
Download
Lenovo 10AS User Manual Download Page 62

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 66.

Replacing the heat sink and fan assembly

Attention:

Do not open your computer or attempt any repair before reading and understanding the

“Important safety information” on page v.

This section provides instructions on how to replace the heat sink and fan assembly.

CAUTION:

The heat sink and fan assembly might be very hot. Before you open the computer cover, turn off the
computer and wait several minutes until the computer is cool.

To replace the heat sink and fan assembly, do the following:

1. Turn off the computer and disconnect all power cords from electrical outlets.

2. Remove the computer cover. See “Removing the computer cover” on page 35.

3. Lay the computer on its side for easier access to the system board.

4. Locate the heat sink and fan assembly. See “Locating components” on page 12.

5. Disconnect the heat sink and fan assembly cable from the microprocessor fan connector on the system

board. See “Locating parts on the system board” on page 13.

50

ThinkCentre E73 User Guide

Summary of Contents for 10AS





















































































































































Reviews:

No comments