manualshive.com logo in svg

Lenovo 10AS, User Manual, Page: 25 / 148

Share
Download
Lenovo 10AS User Manual Download Page 25

Locating parts on the system board

Figure 4 “System board part locations” on page 13 shows the locations of the parts on the system board.

Figure 4. System board part locations

1

4-pin power connector

2

Microprocessor

3

Microprocessor fan connector

4

Memory slot 1 (DIMM1)

5

Memory slot 2 (DIMM2)

6

Thermal sensor connector

7

Power fan connector

8

Hard disk drive/ Optical drive power connectors

9

14-pin power connector

10

BIOS ROM

11

SATA 3.0 connectors

12

Power supply fan connector

13

SATA 2.0 connector

14

Front panel connector (for connecting LED indicators and

the power button)

15

Front USB connector 1 (for connecting USB

ports 1 and 2 on the front bezel)

16

Front USB connector 2 (for connecting an additional USB

device)

17

Clear CMOS (Complementary Metal Oxide

Semiconductor) /Recovery jumper

18

Serial (COM2) connector

19

Front audio connector

20

Internal speaker connector

21

PCI Express x1 card slots (2)

22

PCI Express x16 graphics card slot

23

System fan connector

24

Battery

Chapter 1

.

Product overview

13

Summary of Contents for 10AS





















































































































































Reviews:

No comments