background image

DC Inverter Multi VRF System 

 

 

Volatile liquid, such as diluent 
or gasoline, will damage the 
appearance of air conditioner. 
Only soft dry cloth and wet 
cloth dipped with neutral 
detergent can be used to 
clean the outer case of air 
conditioner. 

 

Under cooling mode, please 
don't set the room 
temperature too low; keep the 
temperature difference 
between indoor and outdoor 
within 5°C (41°F). 

 

If there are any abnormal 
circumstances (such as 
burning smell, etc.), please 
turn off the unit and cut off the 
main power supply 
immediately, and then contact 

LENNOX

 appointed service 

center. If those abnormal 
circumstances still exit, the 
unit may be damaged and it 
may lead to electric shock or 
fire hazard. 

 

Do not repair the unit by 
yourself. Wrong maintenance 
may cause electric shock or 
fire hazard. Please contact 

LENNOX

 appointed service 

center 

for help. 

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or 
mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning 
use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. 
Cleaning and user maintenance shall not be made by children without supervision. 
Install units according to national wiring codes. 
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified 
person in order to avoid a hazard. 
An all-pole disconnection device which has at least 3mm clearances in all poles, and disconnection must be 
incorporated in the fixed wiring in accordance with the wiring rules. 

LENNOX 

will not assume responsibility for any personal injury or property loss caused 

by improper installation, improper debugging, unnecessary repair or not following the instructions of this manual. 

2 Product Introduction 

LENNOX

 Multi VRF System adopts inverter compressor technology. By changing the displacement of 

compressor, stepless capacity regulation within range of 10%~100% can be realized. Various product 
lineups are provided with capacity range from 22.4kW to 35kW, which can be widely used in residential, 
commercial and working area and especially applicable to places with big load change. 

LENNOX

 residential 

air conditioner is absolutely your best choice. 

Summary of Contents for VEPS075N432K









































Reviews: