manualshive.com logo in svg

Lennox MWCB Series, User Manual, Page: 6 / 8

Share
Download
Lennox MWCB Series User Manual Download Page 6

6

Wireless Remote Controller Screen Indicators

Information is displayed when the Wireless Remote Controller is powered on.

Transmission Indicator

MODE display

TIMER ON display

FAN SPEED display

TIMER OFF display

Silence  feature 

display

ECO display

GEAR display

LOCK display

Up/Down louver swing 

display
Not applicable to this

model.

TURBO mode display

Not applicable for

this unit

Temperature/Timer/Fan speed/

Relative Humidity display

Active Clean

 feature display

Sleep

 feature display

Follow Me

 feature display

Not applicable for this unit
Low battery detection (flashing)

Note:

All icons are shown for display purposes only.

During actual unit operation, only active icons are displayed.

Displays when LOCK feature

is activated.

Silence 

LOW

MED

HIGH

AUTO

Lights up when remote 

sends signal to indoor 

unit 

Displays selected fan speed:

Displays the current 

including:   

mode, 

2%-20%

21%-40%

41%-60%
61%-80%
81%-100%

 1%

NOTE - Fan speed cannot be 

adjusted in AUTO or DRY mode. 

Displays when ECO 

feature is activated

Displays when GEAR 

feature  is activated

Displays the set temperature

by default, or fan speed or

timer setting when using

TIMER ON/OFF functions.

Temperature range:

 

Timer setting range: 

0-24 hours

Fan speed setting range: 

AU -100%

This display is blank when

operating in FAN mode. 

g

g g g

g

Breeze Away

 feature display

60-86°F / 16-30°C

Summary of Contents for MWCB Series









Reviews:

No comments