background image

Please contact the local agent for installation.

Indoor unit

1. There should be no obstruction near air

inlet and air outlet.

2. Select a location where the condensat-

ion water can be dispersed easily and

won't affect other people.

Select a location which is convenient to

connect the outdoor unit and near the

power socket.

Select a location which is out of reach

for children.

The location should be able to withstand

the weight of indoor unit and won't incr-

ease noise and vibration.

1.The place with strong heat sources,

   or volatile objects spread in the air.    

,

The place with high-frequency

devices (such as welding machine,

medical equipment).

The place near coast area.

The place with oil or fumes in the air.

3.

2.

4.

5.

5.The place with sulfureted gas.

6.

7.

6. The appliance must be installed 2.5m

8.

7. Don't install the indoor unit right above

the electric appliance.

8. Please try your best to keep way from

Outdoor unit

1.

2.

3.

4. Make sure that the installation follows the requirement of installation

dimension diagram.

Select a location which is out of reach for children and far away from animals

or plants. If it is unavoidable, please add the fence for safety purpose.

5.

2

3

Tools for installation

Selection of installation location

Basic requirement

Installing the unit in the following pla-

ces may cause malfunction. If it is un-

avoidable, please consult the local dealer:

3.

4.

Select a location where the noise and outflow air emitted by the outdoor unit

The location should be well ventilated and dry, in which the outdoor unit

won't be exposed directly to sunlight or strong wind.

The location should be able to withstand the weight of outdoor unit.

1 Level meter
4 Drill head
7 Open-end wrench
10 Vacuum pump

13 Inner hexagon spanner

2 Screw driver
5 Pipe expander
8 Pipe cutter
11 Pressure meter

3 Impact drill
6 Torque wrench
9 Leakage detector
12 Universal meter

14 Measuring tape

Other places with special circumstances.

The appliance shall not be installed

in the laundry.

It’s not allowed to be installed on the 

unstable or motive base structure (such 

as truck) or in the corrosive environ-

ment (such as chemical factory). 

    will not affect neighborhood.

Note:

Summary of Contents for LM012HI-115P432-1X













































Reviews: