background image

08/06

504,954M

*2P0806*

*P504954M*

Page 1

2006 Lennox Industries Inc.

Dallas, Texas, USA

RETAIN THESE INSTRUCTIONS

FOR FUTURE REFERENCE

WARNING

Improper installation, adjustment, alteration, ser-
vice or maintenance can cause personal injury, loss
of life, or damage to property.

Installation and service must be performed by a
qualified installer or service agency.

CAUTION

Physical contact with metal edges and corners
while applying excessive force or rapid motion can
result in personal injury. Be aware of, and use
caution when working near these areas during
installation or while servicing this equipment.

IMPORTANT

This unit must be matched with an indoor coil as
specified in Lennox’ Engineering Handbook.
Coils previously charged with HCFC−22 must be
flushed.

IMPORTANT

The Clean Air Act of 1990 bans the intentional vent-
ing of refrigerant (CFC’s, HFC’s, and HCFC’s) as of
July 1, 1992. Approved methods of recovery, recycl-
ing or reclaiming must be followed. Fines and/or in-
carceration may be levied for noncompliance.

INSTALLATION
INSTRUCTIONS

HPXA16

 

Series Units

HEAT PUMP UNITS

504,954M
08/06
Supersedes 03/06

Table of Contents

HPXA16 Outdoor Unit

1

. . . . . . . . . . . . . . . . . . . . . . . . . . 

Shipping & Packing List

2

. . . . . . . . . . . . . . . . . . . . . . . . 

General Information

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . 

Unit Dimensions

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Parts Arrangement

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Setting the Unit

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Electrical

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Refrigerant Piping

6

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Refrigerant Metering Device

8

. . . . . . . . . . . . . . . . . . . . 

Flushing Existing Line Set & Indoor Coil

8

. . . . . . . . . . 

Manifold Gauge Set

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . 

Service Valves

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Leak Testing

11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Evacuation

12

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Start−Up

12

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Refrigerant Charging 

12

. . . . . . . . . . . . . . . . . . . . . . . . . . 

System Operation

15

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Defrost System

16

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Maintenance

21

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Optional Accessories

21

. . . . . . . . . . . . . . . . . . . . . . . . . . 

Check Points

22

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Homeowner Information:

Maintenance

23

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Thermostat Operation

24

. . . . . . . . . . . . . . . . . . . . . . . . . . 

HPXA16 Outdoor Unit

Lennox HPXA16 outdoor units use HFC−410A refrigerant.
This unit must be installed with a matching indoor coil and
line set as outlined in the Lennox Engineering Handbook.
Elite

®

 Series HPXA16 outdoor units are designed for use

in check expansion valve (CTXV) systems only and must
not be used with other refrigerant flow control devices.

See Lennox Engineering Handbook list of indoor expan-
sion valve kits (ordered separately).

Litho U.S.A.

Summary of Contents for HPXA16 -060

























Reviews: