background image

506257-01

Issue  1330

Page  1  of  29

The equipment covered in this manual is to be installed by trained and experienced 

service and installation technicians. Improper installation, modification, service, or use 

can cause electrical shock, fire, explosion, or other conditions which may cause personal 

injury, death, or property damage. Use appropriate safety gear including safety glasses 

and gloves when installing this equipment.

 

WARNING

Installation and servicing of air conditioning equipment 

can be hazardous due to internal refrigerant pressure 

and live electrical components. Only trained and 

qualified  service  personnel  should  install  or  service 

this equipment. Installation and service performed by 

unqualified  persons  can  result  in  property  damage, 

personal injury, or death.

  WARNING

Sharp metal edges can cause injury. When installing 

the unit, use care to avoid sharp edges.

  WARNING

INSTALLATION AND MAINTENANCE INSTRUCTIONS

4SHP18LT SERIES

Split System Heat Pump

These instructions must be read and understood completely before attempting installation.

Risk of electrical shock. Disconnect all remote power 

supplies before installing or servicing any portion of the 

system. Failure to disconnect power supplies can result 

in property damage, personal injury, or death.

  WARNING

TABLE OF CONTENTS

INSTALLATION  ......................................2

CONNECTION DIAGRAM .......................4

START-UP .............................................13

OPERATION ..........................................18

MAINTENANCE ....................................23

WARRANTY ..........................................28

Manufactured By

Allied Air Enterprises, Inc.

A Lennox International Inc. Company

215 Metropolitan Drive

West Columbia, SC 29170

*P506257-01*

(p)  506257-01

Summary of Contents for Allied Air 4HP18LT- 24






























Reviews: