background image

Page 26

HEATING SEQUENCE CONTINUED

NORMAL HEATING MODE

ABNORMAL HEATING MODE

FLAME RECTIFICATION CURRENT

CHECK. CAN FLAME BE PROVEN WITHIN

4 SECONDS AFTER GAS VALVE OPENS?

(

u

0.15 microamps)

FLAME PRESENT?

INDOOR BLOWER ON DELAY BEGINS

(45 seconds.)

PRIMARY AND SECONDARY LIMIT

SWITCHES CLOSED?

COMBUSTION AIR PRESSURE

SWITCH CLOSED?

LOW FLAME SIGNAL

(Does not affect operation of control)

LED #1 −− SLOW FLASH

LED #2 −− FAST FLASH

GAS VALVE DE−ENERGIZED.

COMBUSTION AIR INDUCER DE−ENERGIZED.

INDOOR BLOWER ON UNTIL SWITCH CLOSES.

LED #1 −− SLOW FLASH. LED #2 −− ON.

IS LIMIT SWITCH CLOSED?

GAS VALVE DE−ENERGIZED.

COMBUSTION AIR INDUCER ON.

INDOOR BLOWER OFF WITH DELAY

LED #1 −− OFF. LED #2 −− SLOW FLASH.

HAS CAB SWITCH CLOSED IN 2.5 MINUTES?

15-SECOND COMBUSTION AIR INDUCER PREPURGE

INITIATED BY CLOSED PRESSURE SWITCH.

YES

IGNITOR WARM-UP −− 20 SECONDS.

YES

4-SECOND TRIAL FOR IGNITION.

GAS VALVE OPENS. IGNITOR ENERGIZED FOR 1

SECOND AFTER VALVE OPENS. CONTROL

10M9301: IGNITOR ENERGIZED DURING TRIAL

UNTIL FLAME SENSED.

YES

FLAME STABILIZATION PERIOD.

GAS VALVE OFF. COMBUSTION AIR INDUCER ON.

INDOOR BLOWER OFF.

HAS CONTROL FAILED TO SENSE FLAME FOR

FIVE CONSECUTIVE TRIES DURING A SINGLE

HEAT DEMAND?

WATCHGUARD MODE. GAS VALVE OFF.

COMBUSTION AIR INDUCER OFF.

INDOOR BLOWER OFF WITH DELAY

LEDs SIGNAL WATCHGUARD FAILURE CODE.

IS 60-MINUTE RESET PERIOD COMPLETE?

YES

4 SECONDS

YES

HAS CONTROL RESET IGNITION

SEQUENCE FOUR TIMES?

FLAME SIGNAL ABOVE 0.2 MICROAMPS?

YES

YES

YES

ROLLOUT SWITCH CLOSED?

GAS VALVE POWER OFF. 

COMBUSTION AIR INDUCER POWER ON.

INDOOR BLOWER ON

LED #1 −− ON. LED #2 −− SLOW FLASH.

SEQUENCE HOLDS UNTIL ROLLOUT SWITCH IS RESET

AND MAIN POWER IS INTERUPTED OR 

THERMOSTAT IS CYCLED OFF/ON FOR 1 TO 20 SEC.

YES

THERMOSTAT DEMAND SATISFIED.

LED #1 & #2 SIMULTANEOUS SLOW FLASHES.

COMB. AIR INDUCER CONTINUES 5-SECOND

POST PURGE AFTER T’STAT DEMAND IS SATISFIED.

INDOOR AIR BLOWER COMPLETES SELECTED

OFF" DELAY BEFORE SHUTTING OFF.

YES

NO

5-MINUTE PRESSURE SWITCH

WATCHGUARD MODE.

YES

IS THERE A PROPER GROUND?

IS VOLTAGE ABOVE 75 VOLTS?

IS IGNITOR INTACT AND CONNECTED?

LEDS SIGNAL

ALTERNATING

FAST FLASH

NO

YES

YES

YES

YES

YES

NO

NO

NO

NO

NO

NO

NO

NO

YES

YES

NO

NO

NO

NO

YES

YES

HAS PRIMARY SECONDARY

LIMIT RESET (CLOSED)

 WITHIN 3 MINUTES?

LIMIT SWITCH

WATCHGUARD

MODE. GAS VALVE

OFF. COMB. AIR 

INDUCER OFF. 

INDOOR BLOWER

OFF WITH DELAY.

LED#1−SLOW

FLASH LED#2− ON.

IS 60−MINUTE 

RESET PERIOD

COMPLETE?

Summary of Contents for 80UGH



































Reviews: