manualshive.com logo in svg

Lennox 12U67, Operating, Troubleshooting And Technical Cheat Sheet, Page: 16 / 21

Share
Download
Lennox 12U67 Operating, Troubleshooting And Technical Cheat Sheet Download Page 16

- 16 -

8. IComfort

®

 Mobile Setup Application

8.1. Operating System Requirements

Dealer commissioning application (iComfort

®

 Mobile Setup) is available for both IOS 6.0 and higher (App Store) and

Android 4.1 and higher (Google Play).

8.2. Commissioning

To commission a system using the iComfort

®

 Mobile Setup Application perform the following:

NOTE 

- It is recommend that when using the iComfort

®

 Mobile Setup application to commission the system, remove

the HD Display from the Mag-Mount before starting. Once commissioning is completed, reattached the HD Display to
the Mag-Mount.

A.

Download and install the iComfort

®

 Mobile Setup Application.

B.

Go to the Smart Hub and press the center Lennox button once.

C.

The center ring LED will start blinking green for two minutes. During that time the Smart Hub will broadcast its
Wi-Fi identifier (SSID).

D.

Go to your mobile device's Wi-Fi connection tool and locate the Smart Hub Wi-Fi broadcast identifier. The identifi­
er (SSID) is 

Direct E300-5200

 for example.

NOTE 

- Refer to your mobile device's owners manual on how to use your Wi-Fi Connection tool.

E.

To connect to the Smart Hub use the last eight digits of the Smart Hub SSID as the password (example
E3005200).

F.

Once connected to the mobile device the Smart Hub center ring LED turns solid green.

G.

Start the  iComfort Mobile Setup Application and make sure you connect to the correct Smart hub by checking
the serial number

NOTE 

- The serial number check is only needed if multiple Smart Hubs are shown. For example if you have three

systems and have completed commissioning of two and while on third unit, the other two Smart hubs connection
data is still listed in the 

 

iComfort Mobile Setup Application. If you chose the wrong one it will not connect because it

would have already stopped broadcasting its connection signal.

H.

Press the 

remote in

 tab on the  iComfort

®

 Mobile Setup Application home screen. This will take you to the com­

missioning screen.

NOTE 

- If the system has not been commissioned it will go to commissioning screen. If the system has already

been commissioned it will go to dealer control center.

I.

Once the commissioning is completed, exit the  iComfort

®

 Mobile Setup Application.

J.

Go to the mobile device's Wi-Fi tool and manually disconnect from the Smart Hub. Or if there is no activity after
three minutes the application will automatically disconnect from the Smart Hub.

K.

Once disconnected the Smart Hub LED will return to a solid blue.

Summary of Contents for 12U67






















Reviews:

No comments