16
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
t
i
K
n
o
i
s
r
e
v
n
o
C
s
a
G
e
n
a
p
o
r
P
o
T
l
a
r
u
t
a
N
.
o
N
s
l
e
d
o
M
e
p
y
T
t
i
n
U
.
o
N
g
o
l
a
t
a
C
T
S
V
B
E
F
P
V
B
E
t
l
o
v
il
li
m
8
9
1
2
H
c
i
n
o
r
t
c
e
l
e
0
0
2
2
H
t
i
K
n
o
i
s
r
e
v
n
o
C
s
a
G
e
n
a
p
o
r
P
o
T
l
a
r
u
t
a
N
.
o
N
s
l
e
d
o
M
e
p
y
T
t
i
n
U
.
o
N
g
o
l
a
t
a
C
R
C
V
B
E
L
C
V
B
E
t
l
o
v
il
li
m
8
9
1
2
H
c
i
n
o
r
t
c
e
l
e
0
0
2
2
H
t
i
K
n
o
i
s
r
e
v
n
o
C
s
a
G
l
a
r
u
t
a
N
o
t
e
n
a
p
o
r
P
.
o
N
l
e
d
o
M
e
p
y
T
t
i
n
U
.
o
N
g
o
l
a
t
a
C
T
S
V
B
E
F
P
V
B
E
t
l
o
v
il
li
m
9
9
1
2
H
c
i
n
o
r
t
c
e
l
e
1
0
2
2
H
t
i
K
n
o
i
s
r
e
v
n
o
C
s
a
G
l
a
r
u
t
a
N
o
t
e
n
a
p
o
r
P
.
o
N
l
e
d
o
M
e
p
y
T
t
i
n
U
.
o
N
g
o
l
a
t
a
C
R
C
V
B
E
L
C
V
B
E
t
l
o
v
il
li
m
3
0
2
2
H
c
i
n
o
r
t
c
e
l
e
5
0
2
2
H
GAS CONVERSION KITS
In Canada:
THE CONVERSION SHALL BE CARRIED OUT
IN ACCORDANCE WITH THE REQUIREMENTS
OF THE PROVINCIAL AUTHORITIES HAVING
JURISDICTION AND IN ACCORDANCE WITH
THE REQUIREMENTS OF THE CAN1-B149.1
AND .2 INSTALLATION CODE.
LA CONVERSION DEVRA ÊTRE EFFECTUÉE
CONFORMÉMENT AUX RECOMMANDATIONS
DES AUTORITÉS PROVINCIALES AYANT
JURIDICTION ET CONFORMÉMENT AUX
EXIGENCES DU CODE D'INSTALLATION CAN1-
B149.1 ET.2.
Gas conversion kits are available to convert
your appliance from the use of one type of gas
to the use of another. These kits contain all the
necessary components needed to complete
the task including labeling that must be affixed
to ensure safe operation.
Kit part numbers are listed here and the follow-
ing steps detail the conversion procedure.
AVERTISSEMENT: CET ÉQUIPEMENT DE CONVERSION
SERA INSTALLÉ PAR UNE AGENCE QUALIFIÉE DE SER-
VICE CONFORMÉMENT AUX INSTRUCTIONS DU
FABRICANT ET TOUTES EXIGENCES ET CODES
APPLICABLES DE L'AUTORISÉS AVOIR LA JURIDICTION.
SI L'INFORMATION DANS CETTE INSTRUCTION N'EST
PAS SUIVIE EXACTEMENT, UN FEU, EXPLOSION OU PRO-
DUCTION DE PROTOXYDE DE CARBONE PEUT RÉSULTER
LE DOMMAGES CAUSER DE PROPRIÉTÉ, PERTE OU
BLESSURE PERSONNELLE DE VIE. L'AGENCE QUALIFIÉE
DE SERVICE EST ESPONSABLE DE L'INSTALLATION
PROPRE DE CET ÉQUIPMENT. L'INSTALLATION N'EST
PAS PROPRE ET COMPLÉTE JUSQU'À L'OPÉRATION DE
L'APPAREIL CONVERTI EST CHÉQUE SUIVANT LES
CRITÈRES ÉTABLIS DANS LES INSTRUCTIONS DE
PROPRIÉTAIRE PROVISIONNÉES AVEC L'ÉQUIPEMENT.
WARNING: THIS CONVERSION KIT SHALL BE
INSTALLED BY A QUALIFIED SERVICE AGENCY IN
ACCORDANCE WITH THE MANUFACTURER'S IN-
STRUCTIONS AND ALL APPLICABLE CODES AND
REQUIREMENTS OF THE AUTHORIZED AGENCY
HAVING JURISDICTION. IF THE INFORMATION IN
THESE INSTRUCTIONS IS NOT FOLLOWED EX-
ACTLY, A FIRE, EXPLOSION OR PRODUCTION OF
CARBON MONOXIDE MAY RESULT CAUSING
PROPERTY DAMAGE, PERSONAL INJURY OR LOSS
OF LIFE. THE INSTALLATION IS NOT PROPER AND
COMPLETE UNTIL THE OPERATION OF THE CON-
VERTED APPLIANCE IS CHECKED AS SPECIFIED IN
THE OWNER INSTRUCTIONS SUPPLIED WITH THE
KIT. THE QUALIFIED SERVICE AGENCY PERFORM-
ING THIS INSTALLATION ASSUMES RESPONSI-
BILITY FOR THIS CONVERSION.
b.
Remove the bottom control compartment
access panel by compressing the spring-
loaded hinge pin on the left side until it
disengages from the left cabinet panel
hole. Pull the panel away from the fire-
place.
See Figure 20 on page 12.
c.
Remove the modesty panel by pulling the
bottom right corner of the modesty panel
out slightly to disengage the snap-fit fea-
ture; lift the modesty panel by the tab on
the panel's right end, pull the right end of
the panel away from the cabinet and then
pull the panel diagonally out of the left side
cabinet panel slots. (In the above proce-
dure, reverse the words "left" and "right"
for EBVCR models). Remove the modesty
panel carefully, so that none of the wires
become loose or disconnected.
d.
Locate the latch at the top of the control
compartment. To disengage the latch from
the bottom vee-flange of the glass enclo-
sure panel, reach for the handles located
towards the back of the latch and pull the
handl down toward the front of the unit.
e.
Swing the bottom of the door out and raise
it slightly to lift the top flange of the door
frame away from the appliance.
Step 2.
Carefully remove the logs.
Exercise
care as not to break the logs
.
Step 3.
Referring to
Figure 29 on page 17
,
remove the burner.
Step 1.
Turn off the gas supply to the appliance.
a.
Open the control compartment access panel,
by actuating the spring-loaded magnetic
catches securing the panel, gently depress-
ing the outer top corners of the panel until the
catches "pop" the panel free and allowing it to
swing out and down to open.
