Version 1.0
2021-07-23
Lemon Microbrick Reference
G
uide
Contents
Introduction .......................................................................................................................................... 2
Features ............................................................................................................................................ 3
Applications for the Microbrick ........................................................................................................ 3
Supply Voltage .................................................................................................................................. 4
Speed Controller and Failsafe .......................................................................................................... 4
Basic Setups .......................................................................................................................................... 4
Connecting the Microbrick ................................................................................................................... 5
Setting Up the Microbrick .................................................................................................................... 5
Specific Issues ..................................................................................................................................... 10
Rudder Steering .............................................................................................................................. 10
Throttle Features ............................................................................................................................ 10
Indicator LEDs ................................................................................................................................. 11
Binding ............................................................................................................................................ 11
Programming ...................................................................................................................................... 11
Transmitter or Microbrick? ............................................................................................................ 11
Programming the Microbrick ......................................................................................................... 12
Swapping the Functions of the Onboard Servos ........................................................................ 12
Changing Stabilization Response Direction ................................................................................ 12
Selecting a Receiver Mix ............................................................................................................. 13
Enabling Dual Aileron Stabilization ............................................................................................ 14
Mixing Considerations .................................................................................................................... 14
Master Gain ........................................................................................................................................ 16
Troubleshooting ................................................................................................................................. 16
ANNEX A: Tips, Tricks and Modifications ........................................................................................... 18
The Variants of the Microbrick. ...................................................................................................... 18
Adding an External Bind Function. ................................................................................................. 18
Mounting the Microbrick with double sided tape. ........................................................................ 19
Power Supply Voltage and the Onboard Speed Controller............................................................ 19
