Disassemble and Wash:
Wash the Stainless Steel Wheatgrass Juicer in hot soapy water prior to use. It should also be washed after every use under
running water in order to flush out vegetable residue and then hand dry. The juicer may also be cleaned in the dishwasher
on the upper rack but hand washing is always preferred to extend the product life.
CLEANING AND MAINTENANCE
2
3
IT IS IMPORTANT TO READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND SAFEGUARDS PRIOR TO USE
1. Always ensure that the appliance is properly assembled and safely set up before use.
2.
DO NOT
attempt to juice frozen foods, nuts, hard fruits, vegetables, or non food items.
3.
Caution:
This appliance is not recommended for use near or by children or persons with certain disabilities. Set up and
store the appliance in a secure dry location out of reach of children.
4. The appliance is designed for domestic use and not for commercial purposes.
5. Use the appliance with supplied accessories only. Warning: the use of accessories or attachments not recommended or
sold by the manufacture may cause injury, damage to personal property and may void your warranty.
6.
Warning:
Do not use while under the influence of alcohol or prescription or non-prescription drugs as these may
impair user’s ability to properly assemble or safely operate the appliance.
7. The manufacturer declines any responsibility in the case of improper use of this product. Improper use of this product
voids the warranty.
8. Avoid contacting moving parts. Wait until all parts have come to a complete stop before removing any parts of the juicer.
9. Keep your work area clean and well lit. Cluttered work benches and dark work areas may cause accidents or injury.
10. Thoroughly hand-wash all appliance parts in warm soapy water prior to use. Do not soak.
11. Tie back loose hair and clothing. Remove neckties, rings, watches, bracelets or other jewelry before operating
the juicer.
12.
Failure to follow warnings and a safety information could result in death serious bodily injury and or property loss.
13.
WARNING:
To avoid dangers of suffocation, keep all plastic bags away from babies and children.
14.
WARNING:
The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible
conditions or situations that could occur. It must be understood by the operator that common-sense must be used.
15.
SAVE THESE INSTRUCTIONS
GENERAL WARNINGS AND SAFETY INFORMATION
Roots and Harvest • West Chester, OH 45011 • 877-509-3457 • RootsandHarvest.com
Roots and Harvest • West Chester, OH 45011 • 877-509-3457 • RootsandHarvest.com
1. Trim the wheatgrass so you have about 2-3 handfuls of grass.
2. Place a small glass or bowl under the 3 holes where the juice will flow.
3. Place another small container at the end of the juicer where the waste will be expelled.
4. Put the wheatgrass into the opening at the top of the juicer.
5. Crank the handle and watch the juice fill your container while the dry, shredded waste will press out the
end of the juicer.
This wheatgrass juicer can also be used to juice soft fruits or other leafy or cooked vegetables.
JUICER USE AND OPERATION
ASSEMBLY
After unit has been cleaned you are ready to assemble and use your Wheatgrass Juicer.
1. Check to ensure the bushing is installed in the back of the juicer head.
•
If not place the bushing on the back of the auger with the flat side nearest the auger curls. Line up the drive
end of the auger with the hole in the back of the juicer and then use a rubber mallet to gently tap the bushing
into place by tapping on the auger.
• Bushing is fully installed when you can install the auger and the retaining ring with gasket. If the retaining
ring cannot easily thread on the bushing is not fully seated in the back of the juicer. You will need to tap on
the auger some more to fully seat the bushing in place.
2. Insert the screen into the wheatgrass juicer.
• Press the screen into place until the end of the screen is even with the front of the unit.
3. Install the rubber gasket inside of the retaining ring which is also the waste extruding end.
4. Screw the retaining ring on just hand tight, do not over tighten.
•
NOTE:
Turn the retaining ring to the
RIGHT
to
LOOSEN
(L) and to the
LEFT
to
TIGHTEN (
T
)
. This is opposite
the norm.
5. Install the handle on the back of the auger by lining up the notch on the handle with the groove in the drive end
of the auger.
6. Clamp the juicer onto a firm, steady surface or counter top. (You may want to remove the handle for this step).
• Make sure the rubber feet are installed so not to mar the countertop.
• Tighten
the clamp screw until the juicer is firmly in place and does not wiggle when the handle is turned.
You are now ready to begin juicing!
PARTS
Juicer Body
Auger
Retaining Ring
Rubber Gasket
Filter Screen
Clamp Screw
Rubber Foot (2)
Auger Bushing
Handle
1
2
3
4
5
6
7
8
9