Leitronic AG EA-8-WRL868, Use Instruction, Page: 33 / 40

33
R-Siren Entry-Delay Connect. mode Sensor on.. Type
0: off 0:off 0: Listening-in I / II / III 00: inactive
1: on 1:on 1: Hands-free 0 0 0 01: Normally open contact
0: enabled 10: Plug&Protect (auto-detected at power-on)
1: disabled input-2 is open => Normally open monitoring
input-2 is closed => Normally closed monitoring
5. Press key # . . 11: Normally closed contact

The new register (bit 7 -> bit 0) will be announced
6. Slide function switch to OFF
10.2.3.1.2 Sensor-1 for presence verification
You can also use sensor-1 to monitor missing activity (i.e. no motion detected within a certain period) =>
Alarm message: „Emergency call due to sensor-1“. Therefore you have to activate time-out as below.
How to program presence verification time-out
Please refer to section 9.10.
10.2.3.1.3 Sensor-1 as entry-detector (Gong function)
A sensor-1 activity can also be signalled locally (Gong-function) according to the following procedure:
Example: Sensor-1 shall greet an incoming person with the pre-recorded individual message only on position I.
1. Slide function switch to PROG
2. Enter sequence
* . 9 . 3 . 1 . 7 3 1 # . # .
..

Current register (bit 7 -> bit 0) will be announced followed by “to modify press * . , to stop press # . “
3. If you want to keep current value proceed with step 6. Otherwise start modifying register by pressing
* .
.
4. Enter sequence 0 . 0 . 0 . 0 1 1 . 1 . 0 . .
Unused Gong on.. Gong-type
000: I / II / III 00: Gong
0 1 1 01: --
0: enabled 10: Individual message
1: disabled 11: Beep loud
5. Press key
# .
.

The new register (bit 7 -> bit 0) will be announced
6. Slide function switch to OFF
10.2.3.2 Sensor-2 monitoring
10.2.3.2.1
Sensor-2 as alarm contact
Alarm function for sensor-2 in armed mode can be selected as following:
Example: Sensor 2 is a normally closed contact that should trigger an un-delayed silent alarm on position I/II
1. Slide function switch to PROG
2. Enter sequence
* . 9 . 3 . 1 . 7 5 7 # . # .
. .

Current register (bit 7 -> bit 0) will be announced followed by “to modify press * . , to stop press # . “
3. If you want to keep current value proceed with step 6. Otherwise start modifying register by pressing
* .
.
4. Enter sequence 0 . 0 . 0 . 0 0 1 . 1 . 1 . .
R-Siren Entry-Delay Connect. mode Sensor on.. Type
0: off 0:off 0: Listening-in I / II / III 00: inactive
1: on 1:on 1: Hands-free 0 0 1 01: Normally open contact
0: enabled 10: Emergency-contact according to section 10.2.3.2.2
1: disabled 11: Normally closed contact
5. Press key # . .

The new register (bit 7 -> bit 0) will be announced
6. Slide function switch to OFF
10.2.3.2.2 Sensor-2 as emergency-sensor
If sensor-2 is enabled in section 10.2.3.2 as emergency-contact an emergency-call is triggered if the contact is
Factory default for gong-function sensor-1
000 111 00
Note:

If you do not want to
trigger an alarm on
position I you have to
disable alarm according
to section 10.2.3.1.1
Factory default for sensor-2 monitoring
00 0 000 00, => inactive