11
3.6 Out of range and reconnection
You will hear a warning tone in the headset when you walk out of range of the base. The
headset will be disconnected from the base and the call will be automatically placed on
hold. If you move back inside the range of the base the headset will automatically
reconnect and the call will be active again.
NOTE: If you do not move back inside the base range within 5 minutes the call will be
disconnected.
3.7 Battery level indication
The four LEDs on the top of the headset base indicate the battery level of your headset
battery.
Indication
Battery level
< 20%
One LED on
20%-40%
Two LEDs on
40%-60%
Three LEDs on
60%-80%
Four LEDs on
80%-100%
Manual W9xx.pdf 1 6/27/2016 11:47:56 AM
3.10
You will hear warning beeps in the headset when you walk out of range of the base. If the
headset disconnects due to being out of range, the call will not drop. The headset will
automatically reconnect when you are back in range and the call will be active again.
3.11
11
3.6 Out of range and reconnection
You will hear a warning tone in the headset when you walk out of range of the base. The
headset will be disconnected from the base and the call will be automatically placed on
hold. If you move back inside the range of the base the headset will automatically
reconnect and the call will be active again.
NOTE: If you do not move back inside the base range within 5 minutes the call will be
disconnected.
3.7 Battery level indication
The four LEDs on the top of the headset base indicate the battery level of your headset
battery.
Indication
Battery level
< 20%
One LED on
20%-40%
Two LEDs on
40%-60%
Three LEDs on
60%-80%
Four LEDs on
80%-100%
Manual W9xx.pdf 1 6/27/2016 11:47:56 AM
9
10
13
3.9 Overview of audio signals
Action
Audio indication
Low battery
2 rapid beeps (60 sec repeat)
Nearly out of range
2 beeps
Out of range
2 pitch tone
Back in range
4 rapid beeps
Receiver volume up/down
1 beep
Mute on
2 pitch tone (8 sec repeat)
Mute off
1 beep
Ringer (EH device)
Multi tone (2 sec repeat)
3.10 Registering a new headset to the base
You can register a new primary headset unit to your IPN W9xx base using the following
procedure:
•
Press and hold the ‘TEL’ button on the headset base for five seconds to enter the
registration mode. The ‘TEL’ LED will flash to indicate it is now in registration mode.
•
Press and hold the ‘mute’ button on the headset for five seconds for the headset to
enter the registration mode.
•
The headset will now be registered to the base which will take around 30 seconds.
When the registration has completed, the base ‘TEL’ LED will stop flashing.
3.11 Using the IPN W9xx for call recording
With the IPN W9xx it is possible to connect a normal telephone call to the USB port of your
computer. This feature can be used to record phone calls with voice recording software on
your PC.
You can register a new primary headset unit to your LH270 or LH275 base using the following
Using the LH280 for call recording
With the LH280 it is possible to connect a normal telephone call to the USB port of your
3.13
3.14
NOTE: The LH280 model cannot register to the LH270 or LH275 base.
•
Press and hold the TEL button on the base for five seconds to make the base
enter registration mode. The TEL light will flash showing the base is in registration mode.
•
Press and hold the mute button on the headset for five seconds to make the headset
enter the registration mode.
When the registration has completed, the base TEL light will stop flashing.
11
12
13
3.9 Overview of audio signals
Action
Audio indication
Low battery
2 rapid beeps (60 sec repeat)
Nearly out of range
2 beeps
Out of range
2 pitch tone
Back in range
4 rapid beeps
Receiver volume up/down
1 beep
Mute on
2 pitch tone (8 sec repeat)
Mute off
1 beep
Ringer (EH device)
Multi tone (2 sec repeat)
3.10 Registering a new headset to the base
You can register a new primary headset unit to your IPN W9xx base using the following
procedure:
•
Press and hold the ‘TEL’ button on the headset base for five seconds to enter the
registration mode. The ‘TEL’ LED will flash to indicate it is now in registration mode.
•
Press and hold the ‘mute’ button on the headset for five seconds for the headset to
enter the registration mode.
•
The headset will now be registered to the base which will take around 30 seconds.
When the registration has completed, the base ‘TEL’ LED will stop flashing.
3.11 Using the IPN W9xx for call recording
With the IPN W9xx it is possible to connect a normal telephone call to the USB port of your
computer. This feature can be used to record phone calls with voice recording software on
your PC.
You can register a new primary headset unit to your LH270 or LH275 base using the following
Using the LH280 for call recording
With the LH280 it is possible to connect a normal telephone call to the USB port of your
3.13
3.14
NOTE: The LH280 model cannot register to the LH270 or LH275 base.
•
Press and hold the TEL button on the base for five seconds to make the base
enter registration mode. The TEL light will flash showing the base is in registration mode.
•
Press and hold the mute button on the headset for five seconds to make the headset
enter the registration mode.
When the registration has completed, the base TEL light will stop flashing.
11
12
12
3.8 Making a conference call
Your IPN DECT headset allows a second and third headset to be temporarily connected to
the base so that you can have a three way conference call.
•
Setup the call using the primary headset unit.
•
Once on the call, place the second IPN DECT headset unit on the base charger.
•
After about one second, the headset ‘Online Indicator’ LED of the new headset will
turn on and the base ‘Online Indicator’ LED will flash to indicate the headset is
registering with the base unit.
•
Once the registering has completed, the base ‘Online Indicator’ LED will stop flashing
and the additional headset LED will flash.
•
Once the registration has completed, a confirmation sound will be heard on the
primary headset.
•
Repeat the steps mentioned above to register a third headset.
•
Lift the additional headset from the base and it will enter talk mode. All three
headsets are now in conference mode.
NOTE: The additional headset will only remain registered to the base for the duration of the
call. After the primary headset has ended the call, the unit will return to its normal state.
The IPN DECT headset also allows you to make a conference call between your normal
phone and a PC or MAC computer. To activate this option hold down the PC/USB switch for
four seconds. Both LEDs of the PC/USB and TEL buttons will light. If one of the buttons is
touched again this function will be switched off and the headset will return to the mode of
the button pressed.
Your Leitner LH270 or LH275 headset allows a second and third headset to be temporarily
connected to the base for training or conference calls.
• Set up the call using the primary headset.
• Once on the call, place the second headset on the base charger.*
3.12 Training mode and making a conference call
• After about one second, the headset’s Online Indicator will turn on and the base’s
Online Indicator will flash to indicate that the headset is registering with the base unit.
•
Once the registering has completed, a confirmation sound will be heard on the
primary headset.
•
Lift the additional headset from the base and it will enter talk mode.
•
Repeat the steps above to register a third headset.
12
3.8 Making a conference call
Your IPN DECT headset allows a second and third headset to be temporarily connected to
the base so that you can have a three way conference call.
•
Setup the call using the primary headset unit.
•
Once on the call, place the second IPN DECT headset unit on the base charger.
•
After about one second, the headset ‘Online Indicator’ LED of the new headset will
turn on and the base ‘Online Indicator’ LED will flash to indicate the headset is
registering with the base unit.
•
Once the registering has completed, the base ‘Online Indicator’ LED will stop flashing
and the additional headset LED will flash.
•
Once the registration has completed, a confirmation sound will be heard on the
primary headset.
•
Repeat the steps mentioned above to register a third headset.
•
Lift the additional headset from the base and it will enter talk mode. All three
headsets are now in conference mode.
NOTE: The additional headset will only remain registered to the base for the duration of the
call. After the primary headset has ended the call, the unit will return to its normal state.
The IPN DECT headset also allows you to make a conference call between your normal
phone and a PC or MAC computer. To activate this option hold down the PC/USB switch for
four seconds. Both LEDs of the PC/USB and TEL buttons will light. If one of the buttons is
touched again this function will be switched off and the headset will return to the mode of
the button pressed.
*Your Leitner LH270 or LH275 headset cannot conference with other headset models.
10
12
3.8 Making a conference call
Your IPN DECT headset allows a second and third headset to be temporarily connected to
the base so that you can have a three way conference call.
•
Setup the call using the primary headset unit.
•
Once on the call, place the second IPN DECT headset unit on the base charger.
•
After about one second, the headset ‘Online Indicator’ LED of the new headset will
turn on and the base ‘Online Indicator’ LED will flash to indicate the headset is
registering with the base unit.
•
Once the registering has completed, the base ‘Online Indicator’ LED will stop flashing
and the additional headset LED will flash.
•
Once the registration has completed, a confirmation sound will be heard on the
primary headset.
•
Repeat the steps mentioned above to register a third headset.
•
Lift the additional headset from the base and it will enter talk mode. All three
headsets are now in conference mode.
NOTE: The additional headset will only remain registered to the base for the duration of the
call. After the primary headset has ended the call, the unit will return to its normal state.
The IPN DECT headset also allows you to make a conference call between your normal
phone and a PC or MAC computer. To activate this option hold down the PC/USB switch for
four seconds. Both LEDs of the PC/USB and TEL buttons will light. If one of the buttons is
touched again this function will be switched off and the headset will return to the mode of
the button pressed.
Your Leitner LH270 or LH275 headset allows a second and third headset to be temporarily
connected to the base for training or conference calls.
• Set up the call using the primary headset.
• Once on the call, place the second headset on the base charger.*
3.12 Training mode and making a conference call
• After about one second, the headset’s Online Indicator will turn on and the base’s
Online Indicator will flash to indicate that the headset is registering with the base unit.
•
Once the registering has completed, a confirmation sound will be heard on the
primary headset.
•
Lift the additional headset from the base and it will enter talk mode.
•
Repeat the steps above to register a third headset.
12
3.8 Making a conference call
Your IPN DECT headset allows a second and third headset to be temporarily connected to
the base so that you can have a three way conference call.
•
Setup the call using the primary headset unit.
•
Once on the call, place the second IPN DECT headset unit on the base charger.
•
After about one second, the headset ‘Online Indicator’ LED of the new headset will
turn on and the base ‘Online Indicator’ LED will flash to indicate the headset is
registering with the base unit.
•
Once the registering has completed, the base ‘Online Indicator’ LED will stop flashing
and the additional headset LED will flash.
•
Once the registration has completed, a confirmation sound will be heard on the
primary headset.
•
Repeat the steps mentioned above to register a third headset.
•
Lift the additional headset from the base and it will enter talk mode. All three
headsets are now in conference mode.
NOTE: The additional headset will only remain registered to the base for the duration of the
call. After the primary headset has ended the call, the unit will return to its normal state.
The IPN DECT headset also allows you to make a conference call between your normal
phone and a PC or MAC computer. To activate this option hold down the PC/USB switch for
four seconds. Both LEDs of the PC/USB and TEL buttons will light. If one of the buttons is
touched again this function will be switched off and the headset will return to the mode of
the button pressed.
*Your Leitner LH270 or LH275 headset cannot conference with other headset models.
10
3.11 Battery level indication
10
11
11
3.6 Out of range and reconnection
You will hear a warning tone in the headset when you walk out of range of the base. The
headset will be disconnected from the base and the call will be automatically placed on
hold. If you move back inside the range of the base the headset will automatically
reconnect and the call will be active again.
NOTE: If you do not move back inside the base range within 5 minutes the call will be
disconnected.
3.7 Battery level indication
The four LEDs on the top of the headset base indicate the battery level of your headset
battery.
Indication
Battery level
< 20%
One LED on
20%-40%
Two LEDs on
40%-60%
Three LEDs on
60%-80%
Four LEDs on
80%-100%
Manual W9xx.pdf 1 6/27/2016 11:47:56 AM
3.10
You will hear warning beeps in the headset when you walk out of range of the base. If the
headset disconnects due to being out of range, the call will not drop. The headset will
automatically reconnect when you are back in range and the call will be active again.
3.11
11
3.6 Out of range and reconnection
You will hear a warning tone in the headset when you walk out of range of the base. The
headset will be disconnected from the base and the call will be automatically placed on
hold. If you move back inside the range of the base the headset will automatically
reconnect and the call will be active again.
NOTE: If you do not move back inside the base range within 5 minutes the call will be
disconnected.
3.7 Battery level indication
The four LEDs on the top of the headset base indicate the battery level of your headset
battery.
Indication
Battery level
< 20%
One LED on
20%-40%
Two LEDs on
40%-60%
Three LEDs on
60%-80%
Four LEDs on
80%-100%
Manual W9xx.pdf 1 6/27/2016 11:47:56 AM
9
10
13
3.9 Overview of audio signals
Action
Audio indication
Low battery
2 rapid beeps (60 sec repeat)
Nearly out of range
2 beeps
Out of range
2 pitch tone
Back in range
4 rapid beeps
Receiver volume up/down
1 beep
Mute on
2 pitch tone (8 sec repeat)
Mute off
1 beep
Ringer (EH device)
Multi tone (2 sec repeat)
3.10 Registering a new headset to the base
You can register a new primary headset unit to your IPN W9xx base using the following
procedure:
•
Press and hold the ‘TEL’ button on the headset base for five seconds to enter the
registration mode. The ‘TEL’ LED will flash to indicate it is now in registration mode.
•
Press and hold the ‘mute’ button on the headset for five seconds for the headset to
enter the registration mode.
•
The headset will now be registered to the base which will take around 30 seconds.
When the registration has completed, the base ‘TEL’ LED will stop flashing.
3.11 Using the IPN W9xx for call recording
With the IPN W9xx it is possible to connect a normal telephone call to the USB port of your
computer. This feature can be used to record phone calls with voice recording software on
your PC.
You can register a new primary headset unit to your LH270 or LH275 base using the following
Using the LH280 for call recording
With the LH280 it is possible to connect a normal telephone call to the USB port of your
3.13
3.14
NOTE: The LH280 model cannot register to the LH270 or LH275 base.
•
Press and hold the TEL button on the base for five seconds to make the base
enter registration mode. The TEL light will flash showing the base is in registration mode.
•
Press and hold the mute button on the headset for five seconds to make the headset
enter the registration mode.
When the registration has completed, the base TEL light will stop flashing.
11
12
13
3.9 Overview of audio signals
Action
Audio indication
Low battery
2 rapid beeps (60 sec repeat)
Nearly out of range
2 beeps
Out of range
2 pitch tone
Back in range
4 rapid beeps
Receiver volume up/down
1 beep
Mute on
2 pitch tone (8 sec repeat)
Mute off
1 beep
Ringer (EH device)
Multi tone (2 sec repeat)
3.10 Registering a new headset to the base
You can register a new primary headset unit to your IPN W9xx base using the following
procedure:
•
Press and hold the ‘TEL’ button on the headset base for five seconds to enter the
registration mode. The ‘TEL’ LED will flash to indicate it is now in registration mode.
•
Press and hold the ‘mute’ button on the headset for five seconds for the headset to
enter the registration mode.
•
The headset will now be registered to the base which will take around 30 seconds.
When the registration has completed, the base ‘TEL’ LED will stop flashing.
3.11 Using the IPN W9xx for call recording
With the IPN W9xx it is possible to connect a normal telephone call to the USB port of your
computer. This feature can be used to record phone calls with voice recording software on
your PC.
You can register a new primary headset unit to your LH270 or LH275 base using the following
Using the LH280 for call recording
With the LH280 it is possible to connect a normal telephone call to the USB port of your
3.13
3.14
NOTE: The LH280 model cannot register to the LH270 or LH275 base.
•
Press and hold the TEL button on the base for five seconds to make the base
enter registration mode. The TEL light will flash showing the base is in registration mode.
•
Press and hold the mute button on the headset for five seconds to make the headset
enter the registration mode.
When the registration has completed, the base TEL light will stop flashing.
11
12
12
3.8 Making a conference call
Your IPN DECT headset allows a second and third headset to be temporarily connected to
the base so that you can have a three way conference call.
•
Setup the call using the primary headset unit.
•
Once on the call, place the second IPN DECT headset unit on the base charger.
•
After about one second, the headset ‘Online Indicator’ LED of the new headset will
turn on and the base ‘Online Indicator’ LED will flash to indicate the headset is
registering with the base unit.
•
Once the registering has completed, the base ‘Online Indicator’ LED will stop flashing
and the additional headset LED will flash.
•
Once the registration has completed, a confirmation sound will be heard on the
primary headset.
•
Repeat the steps mentioned above to register a third headset.
•
Lift the additional headset from the base and it will enter talk mode. All three
headsets are now in conference mode.
NOTE: The additional headset will only remain registered to the base for the duration of the
call. After the primary headset has ended the call, the unit will return to its normal state.
The IPN DECT headset also allows you to make a conference call between your normal
phone and a PC or MAC computer. To activate this option hold down the PC/USB switch for
four seconds. Both LEDs of the PC/USB and TEL buttons will light. If one of the buttons is
touched again this function will be switched off and the headset will return to the mode of
the button pressed.
Your Leitner LH270 or LH275 headset allows a second and third headset to be temporarily
connected to the base for training or conference calls.
• Set up the call using the primary headset.
• Once on the call, place the second headset on the base charger.*
3.12 Training mode and making a conference call
• After about one second, the headset’s Online Indicator will turn on and the base’s
Online Indicator will flash to indicate that the headset is registering with the base unit.
•
Once the registering has completed, a confirmation sound will be heard on the
primary headset.
•
Lift the additional headset from the base and it will enter talk mode.
•
Repeat the steps above to register a third headset.
12
3.8 Making a conference call
Your IPN DECT headset allows a second and third headset to be temporarily connected to
the base so that you can have a three way conference call.
•
Setup the call using the primary headset unit.
•
Once on the call, place the second IPN DECT headset unit on the base charger.
•
After about one second, the headset ‘Online Indicator’ LED of the new headset will
turn on and the base ‘Online Indicator’ LED will flash to indicate the headset is
registering with the base unit.
•
Once the registering has completed, the base ‘Online Indicator’ LED will stop flashing
and the additional headset LED will flash.
•
Once the registration has completed, a confirmation sound will be heard on the
primary headset.
•
Repeat the steps mentioned above to register a third headset.
•
Lift the additional headset from the base and it will enter talk mode. All three
headsets are now in conference mode.
NOTE: The additional headset will only remain registered to the base for the duration of the
call. After the primary headset has ended the call, the unit will return to its normal state.
The IPN DECT headset also allows you to make a conference call between your normal
phone and a PC or MAC computer. To activate this option hold down the PC/USB switch for
four seconds. Both LEDs of the PC/USB and TEL buttons will light. If one of the buttons is
touched again this function will be switched off and the headset will return to the mode of
the button pressed.
*Your Leitner LH270 or LH275 headset cannot conference with other headset models.
10
12
3.8 Making a conference call
Your IPN DECT headset allows a second and third headset to be temporarily connected to
the base so that you can have a three way conference call.
•
Setup the call using the primary headset unit.
•
Once on the call, place the second IPN DECT headset unit on the base charger.
•
After about one second, the headset ‘Online Indicator’ LED of the new headset will
turn on and the base ‘Online Indicator’ LED will flash to indicate the headset is
registering with the base unit.
•
Once the registering has completed, the base ‘Online Indicator’ LED will stop flashing
and the additional headset LED will flash.
•
Once the registration has completed, a confirmation sound will be heard on the
primary headset.
•
Repeat the steps mentioned above to register a third headset.
•
Lift the additional headset from the base and it will enter talk mode. All three
headsets are now in conference mode.
NOTE: The additional headset will only remain registered to the base for the duration of the
call. After the primary headset has ended the call, the unit will return to its normal state.
The IPN DECT headset also allows you to make a conference call between your normal
phone and a PC or MAC computer. To activate this option hold down the PC/USB switch for
four seconds. Both LEDs of the PC/USB and TEL buttons will light. If one of the buttons is
touched again this function will be switched off and the headset will return to the mode of
the button pressed.
Your Leitner LH270 or LH275 headset allows a second and third headset to be temporarily
connected to the base for training or conference calls.
• Set up the call using the primary headset.
• Once on the call, place the second headset on the base charger.*
3.12 Training mode and making a conference call
• After about one second, the headset’s Online Indicator will turn on and the base’s
Online Indicator will flash to indicate that the headset is registering with the base unit.
•
Once the registering has completed, a confirmation sound will be heard on the
primary headset.
•
Lift the additional headset from the base and it will enter talk mode.
•
Repeat the steps above to register a third headset.
12
3.8 Making a conference call
Your IPN DECT headset allows a second and third headset to be temporarily connected to
the base so that you can have a three way conference call.
•
Setup the call using the primary headset unit.
•
Once on the call, place the second IPN DECT headset unit on the base charger.
•
After about one second, the headset ‘Online Indicator’ LED of the new headset will
turn on and the base ‘Online Indicator’ LED will flash to indicate the headset is
registering with the base unit.
•
Once the registering has completed, the base ‘Online Indicator’ LED will stop flashing
and the additional headset LED will flash.
•
Once the registration has completed, a confirmation sound will be heard on the
primary headset.
•
Repeat the steps mentioned above to register a third headset.
•
Lift the additional headset from the base and it will enter talk mode. All three
headsets are now in conference mode.
NOTE: The additional headset will only remain registered to the base for the duration of the
call. After the primary headset has ended the call, the unit will return to its normal state.
The IPN DECT headset also allows you to make a conference call between your normal
phone and a PC or MAC computer. To activate this option hold down the PC/USB switch for
four seconds. Both LEDs of the PC/USB and TEL buttons will light. If one of the buttons is
touched again this function will be switched off and the headset will return to the mode of
the button pressed.
*Your Leitner LH270 or LH275 headset cannot conference with other headset models.
10
Mute off/on
While Mute is on
10
11
manual_270-275_v5.indd 10
3/20/2017 1:18:02 PM
