Step #8
With the coupler piece and support arms adjusted properly (about 1/2” away
from cover hinge and centered on spa), using the #10 self tapping screws,
fasten support arms to pivot arms and center coupler piece to the support
arms (see fig. # 7.)
Note: Be sure to rotate the coupler piece so that the inserted
screws are at a horizontal angle with the screw head facing the back of the spa.
Pivot Arm
Center Coupler Piece
Pivot Arm
Support Arm
Figure 7
Figure 8
R
Black Body
Figure 9
3
/
8
" Rubber Sleeve
Figure 9
V
D
Step #9
Using the Covermate, lift the cover off the spa and place it in the upright
position. Snap the gas shocks on the ball studs.
Note: Be sure to install Gas Shocks with the black body on top. (see fig. 8 for
complete look).
Step #10
Attach 3/8” Rubber Sleeve to the end of the Pivot Arm that the Wind Lock Bar
latches onto. (See Fig. 9)
Attach the provided 3 hook TowelMate on the preferred side of your Cover-
mate by simply snapping it into place and inserting the middle self tapping
screw (See Fig 10)
Step #11
Snap on the left and right bracket covers (front and large covers). (See Fig. 11)
You Are Done - Operation of the Covermate III Plastic
1. Fold the first half of the spa cover off the spa. Gripping the rubber grip.
Motion the spa cover into its vertical upright position
2. When closing spa cover unlock Wind Lock Bar by lifting up on the bar and
pulling the Covermate down.
CAUTION!
Do not use the Covermate in high wind condition (greater than 10 m.p.h). Injury
from the spa cover being blown over and impacting the spa user can occur.
Front
Large
Figure 11
Figure 10
N
I
ITEM
Part #
Box Content - Description
QTY
A
100028 1 1/8" x 4'10"; 20x40-PAINTED RETAINER RIGHT
1
B
100029 1 1/8" x 4'10"; 20x40-PAINTED RETAINER LEFT
1
C
100002 8" GRIP
2
D
100003 1 1/8" x 3' 7", COUPLER -PAINTED
1
E
100022 1 1/4 x 2' 7"; PIVOT ARM ASSEMBLY-PAINTED
2
F
100344 BUSHING, Plastic Black .8825” Thick
4
G
100023 CM III PLASTIC BRACKET KIT
1
H
100024 1.250" x 1.750" Vinyl black Cap
2
I
100008 TOWELMATE
1
J
100025 CMIII PLASTIC SCREW KIT
1
K
100026 3/8-16 X 2 3/4" Hex Cap Screw
4
L
100011 3/8-16 Thin Nylon INS Locknut
5
M
100012 3/8 USS Flat Washer
5
N
100013 #10 x 5/8 Phillips Pan-Self Tapping screw
12
O
100027 #12 x 1 1/2" Phil Pan screw - mounting
24
P
100031 3/8-16 X 1 CARRIAGE BOLT GR 2 BLACK ZINC
1
Q
100016 Small black dome cap
12
R
100031 5/16-18 BALL STUD BLACK
4
S
100032 5/16-18 THIN NYLON INS L/N ZINC
4
T
100033 RUBBER SLEEVE 1.85"; 1.25" O.D.; .45" I.D.BLK
2
U
100034 HEX PLASTIC CAP DOME BLACK, 5/16
2
V
100035 RUBBER SLEEVE .33" I.D. X .59" O.D. X .38" LONG
1
W
100030 CM III PLASTIC INSTRUCTION SHEET
1
X
100370 Plastic Spacer, .38 I.D. x .75 O.D. x .093 thick
1
Y
100055 Lockbar, .250" thick
1
Back
of
Spa
09J
A
N
0
9
rev.0
1
