manualshive.com logo in svg

Leica BIOSYSTEMS 1404723512, Instructions For Use Manual, Page: 34 / 42

Share
Download
Leica BIOSYSTEMS 1404723512 Instructions For Use Manual Download Page 34

34

Version 2.4, Revision L 

Cleaning and Maintenance 

7

7.2 

Changing the fuse

Warning 

Before changing a fuse, always switch off the instrument first and remove the instrument cable 

completely. The instrument must have cooled down and the paraffin tank must be empty.
When changing a fuse, do NOT use any fuses other than the spare fuses supplied with the 

instrument.

If the instrument fails completely, first check the power supply at the power socket.

Then check the fuses at the rear side of the instrument.

To do so, proceed as follows:

•  Using a screwdriver 

(

→

 Fig.  28-

1

)

, carefully push out the fuse insert 

(

→

 Fig.  28-

2

)

.

•  Remove the fuse insert - it contains two fuses 

(

→

 Fig.  28-

3

)

.

•  Check that the thin wire 

(

→

 Fig.  28-

4

)

 in the glass capillary of a fuse is intact. If not, replace the fuse 

(the standard scope of delivery includes two replacement fuses).

Warning 

Before plugging the power cable back in and switching on the instrument, you must have identified 

and corrected the cause of the burned-out fuse.

•  Insert the fuse insert with the two fuses and start up the instrument again.

Fig. 28   

1

2

3

4

 

Summary of Contents for 1404723512











































Reviews:

No comments