Leibinger 22/4400-00 User Manual Download Page 9

Page: 9 / 15

ATTACHMENTS FOR BATTERY DRILL SYSTEM 4-807 ( GB )

Overview of attachments:

Order number

1.) 22/4415-00

2.) 22/4416-00

3.) 22/4417-00

4.) 22/4413-00
22/4414-00

5.) 22/4411-00
22/4412-00

6.) 22/4534-00

7.) 22/4450-00

8.) 22/4550-00

9.) 22/4455-00

10.) 22/4535-00

11.) 22/4540-00

12.) 22/4536-00

13.) 22/4537-00

14.) 22/4538-00

15.) 22/4539-00

Description:

Long rechargeable battery with extension for Battery Drill System 22/4400-00 increased power output

Standard rechargeable battery

Funnel for inserting Rechargeable Battery 22/4415-00 or 22/4416-00 into Battery Drill System 22/4400-00 (to avoid
contamination

of the Battery Drill System. If it is not used, there may be a loss of sterility)

Desktop Charger, mono 240V and 115V: charging time 60 minutes (Please state required voltage when

ordering)

Desktop Charger, dual 240V and 115V: charging time 60 minutes (Please state required voltage when

ordering)

Three-jaw chuck, 0.5 mm to 7.0 mm capacity for round and triangular shanks, incl. chuck key

Reduction gears with AO standard clutch, large. Speed 0-150 rpm

Oscillating saw with AO connection for saw blades

Sternum saw

Quick-action chuck for Kirschner wires, dia. 0.5 to 3.0 mm

Protection & guidance sleeve for Kirschner wires (screws onto Battery Drill System 22/4400-00 )

Chuck for AO and Aesculap attachments, Standard small

Chuck for DIN attachments (Aesculap medullary reamer)

Harris chuck

Hudson chuck

Summary of Contents for 22/4400-00
















Search results

Summary of Contents for 22/4400-00

Reviews:

Related manuals for 22/4400-00

Brands by name

Popular brands

Leibinger 22/4400-00, User Manual

Search results

Summary of Contents for 22/4400-00

Reviews:

Related manuals for 22/4400-00

Brands by name

Popular brands