LEHR LP 2.5S Operator'S Manual Download Page 13

Page: 13 / 30

LEHR

OPERATION

SHIFTING

WARNING: Before shifting, make sure no swimmers are in the water near your boat.

1. Place the throttle in the slowest position.

2. Move the gear shift lever quickly into gear from neutral to forward .

STOPPING ENGINE

1. Push and hold the engine stop button until the engine completely stops.

2. After the engine has stopped disconnect the propane canister.

ADJUSTING BOAT TRIM

WARNING: Stop the engine before adjusting the trim angle. Use care to avoid being pinched when removing

the trim bolt. Use caution when trying a trim position for the first time. Increase speed gradually

and watch for any signs of instability or control problems. Improper trim angle can cause loss of

control.

•

Reposition the trim bolt inside the desired hole.

•

To raise the bow (”trim-out”), move the trim bolt away from the transom.

•

To lower the bow (”trim-in”), move the trim bolt closer to the transom.

•

Test the boat with the trim set to different angles to find the position that works best for your boat and

operating conditions.

NOTE: The outboard motor trim angle can be changed approximately 4 degrees by shifting the trim bolt one

hole.

When the boat is on plane, a bow-up attitude results in less drag, greater stability and efficiency. This is

generally when the keel line of the boat is up about 3 to 5 degrees. With the bow up, the bow of the boat

may have a greater tendency to steer to one side or the other. Compensate for this as you steer. The trim

tab can also be adjusted to help to help offset this effect. When the bow is down, it is easier to accelerate

from a standing start onto plane.

BOW UP

Too much trim-out puts the bow of the boat too high in the water. Performance and economy are decreased

because the hull of the boat is pushing the water and there is more drag. Excessive trim-out can also cause

the propeller to ventilate, which reduces performance further, and the boat may “porpoise” (hop in the water)

which could throw the operator and passengers overboard.

TRIM BOLT

•

Tilt the engine up slightly.

Summary of Contents for LP 2.5S






























Search results

Summary of Contents for LP 2.5S

Reviews:

Brands by name

Popular brands

LEHR LP 2.5S, Operator'S Manual

Search results

Summary of Contents for LP 2.5S

Reviews:

Brands by name

Popular brands