background image

 

Liftboy 1/2/3 Handbook

 

Stand 01/2019 

 

Liftboy 1/2/3

 

Plattform Lift 

Seite 4 of 10 

Important / Warnings 

 

Please read the whole manual, before the platform is operated 

The installation of the platform is only allowed by 

Lehner Lifttechnik

 or a qualified 

staff recommended by 

Lehner Lifttechnik

The maximum load capacity of each model must not be exceeded. 

The platform is made for the transport of persons, it is only allowed to use the 
platform as how it is described in the manual.  

A simple and serviceable “Emergency Procedure” must be agreed between the 
user and a helper. This is to ensure that the user does not get trapped on the 
platform in the event of electrical or mechanical failure. 

 

Unpacking and preparation 

 

Visual controlI: 

If the packing is damaged at the receipt of the platform, the parts of the platform have to be 
examined exactly, if there are apparent damages or defects. If there is suspect of 
damages, the platform must not be used! The platform has to be examined by the 
company 

Lehner Lifttechnik

 or qualified staff authorized by 

Lehner Lifttechnik

.  

 
 

Standard content: 

1.  Platform and safety curtain 
2.  Access ramp (manual or automatic folding) 
3.  Rail / safety curb 
4.  Electric power supply (transformer or charger) 
5.  Handheld controller 

 

Summary of Contents for Liftboy 1











Reviews: