800.879.8585
www.legrand.us/wattstopper
No. 25099 – 11/16 rev. 1
© Copyright 2016 Legrand All Rights Reserved.
© Copyright 2016 Tous droits réservés Legrand.
© Copyright 2016 Legrand Todos los derechos reservados.
Wattstopper warranties its products to be free
of defects in materials and workmanship for a
period of five (5) years. There are no obligations
or liabilities on the part of Wattstopper for
consequential damages arising out of, or in
connection with, the use or performance of this
product or other indirect damages with respect
to loss of property, revenue or profit, or cost of
removal, installation or reinstallation.
Wattstopper garantit que ses produits sont
exempts de défauts de matériaux et de fabrication
pour une période de cinq (5) ans. Wattstopper
ne peut être tenu responsable de tout dommage
consécutif causé par ou lié à l’utilisation ou
à la performance de ce produit ou tout autre
dommage indirect lié à la perte de propriété, de
revenus, ou de profits, ou aux coûts d’enlèvement,
d’installation ou de réinstallation.
Wattstopper garantiza que sus productos
están libres de defectos en materiales y mano
de obra por un período de cinco (5) años. No
existen obligaciones ni responsabilidades por
parte de Wattstopper por daños consecuentes
que se deriven o estén relacionados con el
uso o el rendimiento de este producto u otros
daños indirectos con respecto a la pérdida
de propiedad, renta o ganancias, o al costo
de extracción, instalación o reinstalación.
WARRANTY INFORMATION
INFORMATIONS RELATIVES À LA GARANTIE
INFORMACIÓN DE LA GARANTÍA
ADJUSTMENT
A “configuration” button allows access to the Wattstopper Push n’ Learn™ technology to change the operation of the LMRH-101.
Step 1: Enter Push n’ Learn (PnL)
1.
Locate the configuration button inside the LMRH-101 battery compartment.
2.
Point the LMRH-101 at a DLM IR device.
3.
Press and hold the configuration button until the red LED in the battery compartment begins blinking (approximately 3 seconds),
then release the button.
4.
Make sure the LMRH-101’s red LED continues to blink, then observe the following:
•
The Red LEDs on all other DLM devices on the network start blinking rapidly (2x/second). The LEDs continue to blink until you
exit PnL.
•
All loads on the DLM local network turn
OFF
immediately after entering PnL. After 1 second, load 1 turns
ON
.
Step 2: Load Selection
A quick press on the LMRH-101’s configuration button turns
OFF
load 1 then turns on the next load in sequence. Keep pressing the
configuration button to step through all the loads connected to the DLM local network. When a load turns
ON
the blue LED is lit brightly
on all switch buttons and sensors bound to the load.
1.
To bind the load to the LMRH-101: While the load is
ON
press the paddle making sure that the blue LED turns
ON
brightly.
2. To unbind a load: While the load is
ON
and the blue LED is brightly lit, press the paddle. The LED goes dim to indicate the paddle
on the handheld remote no longer controls this load.
• A quick press on the configuration button turns
ON
the next load.
• Repeat until the paddle is bound to all the loads you want it to control.
NOTE:
More than one load can be assigned to the paddle and a load can be assigned to multiple devices in the DLM network.
Step 3: Exit Push n’ Learn (PnL)
1.
Point the LMRH-101 at a DLM IR device.
2.
Press and hold the LMRH-101 configuration button until the red LED in the battery compartment stops blinking (approximately
3 seconds), then release the button.
RESET PROCESS
Load binding reset
- To clear the unit so that it is not bound to any load:
1.
Do not point the LMRH-101 toward any DLM IR enabled device.
2.
Press and hold the configuration button in the battery compartment until the red LED goes solid
ON
(approximately 10 seconds).
Device reset
- To get the unit back to its default Plug n’ Go state (bind to all loads):
1.
Do not point the LMRH-101 toward any DLM IR enabled device.
2.
Press and hold the configuration button in the battery compartment for 20 seconds.
System Reset
- This reset returns ALL DLM devices to their factory default PnG settings. All system settings will be reset; all
customized binding relationships will be lost. All PnG functionality will be restored. To return all devices on the DLM local network to PnG
using the LMRH-101:
1.
Point the LMRH-101 at an IR enabled DLM local network device.
2.
Press and hold the configuration button in the battery compartment until the red LED starts blinking to put the DLM local network
into PnL (see Step 1 in ADJUSTMENT for details). Release the button.
3.
Press and hold the configuration button again for approximately 20 seconds, until the red LED on the DLM devices resumes
blinking rapidly (approximately 2x/second).
TROUBLESHOOTING
LED on the remote
doesn’t light.
Press the button. If the LED doesn’t light:
•
Check to see if the LED is actually lit, but very dim. This is normal. Press the top of the button to fully turn
ON
the LED.
•
Check batteries. Replace if needed.
• Remove the batteries for 5 minutes. After 5 minutes, reinstall the batteries and try again.
