background image

7

No: IS-00722  Rev. 2

FIGURE 1A

Start with ring level and

then adjust if needed

STEP 2. Insert bracket/bend wings. 

Place bracket into the 

hole and carefully bend the two sides back around to meet the 

back of the sheetrock as illustrated. Avoid over bending the 

wings. Do not screw sides in until step four.

STEP 3. Secure inside ring. 

Secure inside ring with the two 

screws provided.

STEP 4. Final screws. 

Secure completed assembly using the 

four self tapping screws angled as illustrated – two screws on 

each side. DO NOT OVER TIGHTEN!

STEP 5. Install the Equinox 73-III touchscreen. 

The retrofit 

bracket is now ready to receive an Equinox 73-III touchscreen 

by pressing straight back on both sides at the same time until 

locked and secure.

EQUINOX 73-III RETROFIT STATION INSTALLATION STEPS

Legrand’s Equinox 73-III retrofit install kit is designed to mount the Equinox 73-III touchscreen directly to sheetrock without the 

added cost of the bezel, saving time and money. Installation of the Equinox 73-III should be performed or supervised by a certified 

installer.  Begin by preparing the wall opening. The recommended mounting height is six inches above that of a typical keypad station 

or approximately 50” to 58” from the floor to the bottom of the Equinox 73-III touchscreen. However, it may be installed at any height 

fitting specific custom installation requirements.

NOTE: 

The installer must provide an Ethernet RJ-45 connection wire.  Ethernet cable should be CAT5e or better with PoE or PoE+ 

support.

STEP 1. Cut the sheetrock. 

Cut a precise rectangular hole in the sheetrock – 6-3/8” wide x 4-3/8” high (162mm x 111mm).

The hole should be 

very clean-cut, exact and must be level

. Adjustable tolerances are extremely small and extra care should be 

taken in cutting the hole out. Adjustment to the inside ring (see figure 1A,) is limited or the edge of the install bracket will show.

 

a. Fine tune a small amount by tilting the ring slightly to level screen – see figure 1A below; illustration is exaggerated.

BE

ND

  

 

BEN

D

SHEETROCK

FIG. 2

FIG. 3

FIG. 4

FIG. 5

1

5 - BACK 

VIEW

2

3

4

Summary of Contents for Vantage Equinox 73-III









Reviews: