background image

Plugmold 2000 Aluminum 
Plugmold 2000TR Aluminum 

I N S T A L L A T I O N   I N S T R U C T I O N S

Installation Instruction No.: 1 009 949  –  February 2011

Legrand/Wiremold electrical systems conform to and should be properly
grounded  in  compliance  with  requirements  of  the  current  National
Electrical Code or codes administered by local authorities.

All  electrical  products  may  present  a  possible  shock  or  fire 
hazard  if  improperly  installed  or  used.  Legrand/Wiremold  electrical
products  may  bear  the  mark  of  a  Nationally  Recognized  Testing
Laboratory (NRTL) and should be installed in conformance with current
local and/or the National Electrical Code.

IMPORTANT: Please read all instructions

before beginning.

AL2000 SYSTEM PRODUCT APPLICATIONS

TO INSTALL:

1. Bring Feed into Base

a. Remove appropriate 1/2" trade size entrance knockout in base, or attach Feed End Fitting (AL2010A).

2. Install Base Section on Surface

a. Attach base section on mounting surface using AL2003 Spring Mounting Clips, or by drilling 9/32” holes in the base and use #8

set screws. Ensure holes are free from burrs.

b. If required, cut base to length and carefully debur any cut ends before mounting. If cuts have been made to the base, center the

cover section over the mounted base. Locate, mark and cut the cover ends.  If the edge of any receptacle falls closer than 1 1/2"
[38mm] from the end of the unit, that receptacle must be cut out to allow sufficient space for the installation of an end fitting.

c. Connect multiple sections together using coupler (AL2001). To install, slide coupling plate into both base sections, center on joint

and tighten locking screws.

d. To install around corners, use appropriate elbows, (AL2011 - 90° Flat Elbow), (AL2017 – Internal Elbow), or (AL2017 - External Elbow)

3. Install Ground Adapter

a. Use Ground Adapter (AL2009) provided to secure ground connection. To relocate, loosen set screw and twist counter clockwise.

Position in between receptacles (to avoid interference) and assemble in reverse order.

4. Install Blank End Fitting (AL2010B)

a. At end of base raceway run, slide blank end fitting in last base sections and secure in place by tightening screw.

5. Connect wired section to feed

a. Connect feed wires to wired raceway sections. It is recommended to stagger connection points to allow room for all connections.

6. Snap raceway cover onto base

a. If necessary, snap receptacle harness into cover making sure to line up receptacle faces with pre-punched holes in the raceway cover.
b. Engage lower edge of cover over the edge of the base.  Starting at one end and progressing along the unit, snap in upper edge

of the cover with the heel of the hand. Ensure that wires are pushed completely into the base before assembling the cover to
avoid pinching the wires.

7. Snap on cover clip to cover joint seams where lengths of covers come together.

8. To remove cover, insert removal tool into groove, push down and twist.

NOTE: All mounting methods must result in flush interior surface. 

1

6

4

7

8

5

3

2

2

Summary of Contents for Plugmold 2000 Aluminum

Page 1: ...ust be cut out to allow sufficient space for the installation of an end fitting c Connect multiple sections together using coupler AL2001 To install slide coupling plate into both base sections center on joint and tighten locking screws d To install around corners use appropriate elbows AL2011 90 Flat Elbow AL2017 Internal Elbow or AL2017 External Elbow 3 Install Ground Adapter a Use Ground Adapte...

Page 2: ...ogether Connect wires tighten screws and snap in cover Single Pole Switch 15A 120V To Install slide coupler into groove of AL2400B base raceway and push sections together Tighten screws and snap in cover AL2003 Mounting Clip AL2006 Cover Clip To close any gaps That occur from field cutting snap AL2006 Cover Clip over joints where two adjoining pieces come together Use for external support of racew...

Page 3: ...ten section to surface joints tighten set screws Center coupling over base and tighten screws Install fitting cover after wiring 5 Twist out KOs in cover section where raceway enters Attach cover with screws 6 Attach device if required to cover section 7 Install standard cover plate AL2015 Tee Elbow AL2018 External Elbow AL2015 Tee Fitting position fitting at end of AL2000B base Install other base...

Page 4: ...base Tighten locking screw Attach ground wire using brass cup washer and green hex nut to ground lug AL2051H Box Adapter Use for feed raceway from existing wall outlet box To install attach adapter to outlet box with two screws This system is designed with capacity for additional feed or circuitry conductors 48 1219mm WIREMOLD U S and International 60 Woodlawn Street West Hartford CT 06110 1 800 6...

Reviews: