LEGRAND 0 488 17, Technical Data Sheet

Page: 6 / 7

6/7
CONTENTS
Technical data sheet: S000072383EN-2 Updated: 17/10/2017 Created: 04/10/2012
Catalogue number(s): 0 488 17
Corridor sensor - PIR
Sensor parameters Default
value
Modifiable
parameters
Configuration
tools
0 882 30 0 882 35
Time delay
10 min
3, 5, 10, 15, 20 min −
0 - 59 min 59 s −
Sensitivity
PIR
(very high)/
US (high)
Low, medium,
high, very high
Modes
Auto on/
Auto off
Inactive
Activate/
Deactivate
Walk-through
mode
Active
Activate/
Deactivate
Manual on/
Auto off
Inactive
Activate/
Deactivate
Detection system
Initial PIR and US PIR and/or US,
PIR, US
−
Maintain PIR or US
PIR and/or US,
PIR, US
−
Restart PIR or US
PIR and/or US, PIR,
US, Deactivate
−
Alarm Inactive
Activate/
Deactivate
−
8. SETTINGS
8.1 Detection parameters
Time delay: Length of time the load is on after detection.
Pulse mode (= push-button mode): If the time delay parameter is
at 0, the sensor is in push-button mode. In this case, there is a 10 minute
time delay before the load is switched off. If the setting is overridden or
there is a new detection, the 10 minute time delay starts again.
Available with configuration tool 0 882 30.
Sensitivity: Detection range setting.
Modes:
Auto on/Auto off mode:
Automatic switch-on:
- On detection of presence if the natural light level is insufficient.
Automatic switch-off:
- If no presence is detected and at the end of the set time delay
- Or if the natural light level is sufficient (regulation activated)
Another detection causes automatic switch-on if there is insufficient
light.
Walk-through mode:
- If no presence is detected in the 20 seconds following an initial
detection, the product will cut off the load after 3 minutes.
- If another presence is detected in the 3 minutes following initial
detection, the device will cut off the load at the end of the set time
delay.
Manual on/Auto off mode:
Manual switch-on, automatic switch-off:
- When no presence is detected and at the end of the set time delay.
After switch-off, any new detection within a 30 second period triggers
an automatic switch-on. The Restart function must be activated.
After 30 seconds the device is switched on via a manual switch.
8. SETTINGS (continued)
8.1 Detection parameters (continued)
Detection system:
Initial detection: The load is switched on as soon as the first detection
occurs if the natural light level is below the light level threshold.
Maintain: The load remains active if another presence is detected.
Restart: In manual mode. After switch-off, any new detection within a
30 second period triggers an automatic switch-on.
After 30 seconds the device must be switched on manually.
Possible in Manual on/Auto off mode only.
Alarm: An audible signal is emitted before switch-off (1 minute before,
then 30 seconds, then 10 seconds).
8.2 Light parameters
Light level threshold: Value at which the load comes on if the
natural light level is less than the setting.
Eye function: Value 0 (eye on configuration tool 0 882 30) is
used to save the ambient light level in the room as a light level
threshold.
Advanced mode:
Calibration: The ambient light level measured with a luxmeter
must then be transmitted to the detector.
Regulation: Automatic switch-off of the load 10 minutes after the
light level threshold is exceeded with an additional safety threshold
(to avoid lights switching off at the wrong moment).
Light contribution: Quantity of additional lux provided by the load
being switched on.
When the light contribution parameter is set to "Auto" on the
configuration tool Cat. No. 0 882 30 the sensor automatically calculates
the light contribution.
8.3 Modifying the parameters using the configuration tools
• 0 882 35: Simplified configuration tool
• 0 882 30: Advanced configuration tool
When the sensor receives an IR command via a configuration tool,
it emits a beep confirming that the modification has been taken into
account.
For more information about setting parameters, refer to the data sheet
for the configuration tool Cat. No. 0 882 30.
- Return to factory settings:
1
st
press: Short press on LEARN: the LED flashes slowly.
2
nd
press: Press and hold down LEARN for 10 seconds until the LED
flashes quickly.
Sensor parameters Default
value
Modifiable
parameters
Configuration
tools
0 882 30 0 882 35
Light level threshold
150 lux
20, 100, 300, 500,
1000 lux
−
0 - 1275 lux −
A
dv
anc
ed
mo
de
Calibration
− 0 - 99995 lux −
Regulation
Active
Activate/
Deactivate
−
Light
contribution
Auto Auto - 1275 lux −