manualshive.com logo in svg

Legend Gen X Series, Owner'S Manual, Page: 18 / 24

Share
Download
Legend Gen X Series Owner'S Manual Download Page 18

17

BOAT feATureS continued

horN:

This switch activates the boat’s horn.  Push the switch and hold it to sound the horn.

The livewell system on your boat is designed to supply the water and oxygen needed for the survival of your on-

board fish.   The following instructions will help you understand the livewell system that you have in your boat.

livewell operation:

1. Install the removable Threaded Sure-Lock 

removable stand pipe in the drain fitting inside the 

livewell
2. Turn the flow-adjustment tap counterclockwise in 

the livewell.
3. Start the livewell filling pump using the livewell 

switch that corresponds to your boat.  The water 

will rise in the livewell until it reaches the top of the 

overflow protection pipe.
4. To control the aerator spray. use the flow-

adjustment tap.
5. Turn off the livewell pump once the livewell is full, 

and your are done.
6. Turn pump on every few minutes to refresh water 

Note: 

 If equipped with a horn, you still require a manual sending device according to Canadian Coast guard 

regulations, such as a pealess whistle.

lIveWell:

lIveWell a:

a:

lIveWell B:

lIveWell c:

flow-adjustment tap

Aerator

Aerator

Aerator

flow-adjustment tap

Overflow protection drain 

Drain plug 

Drain 

Drain 

Threaded Sure-Lock 

removable stand pipe with 

overflow protection 

Threaded Sure-Lock 

removable stand pipe with 

overflow protection 

Select Pontoon models

Deluxe Pontoon models

Select gen X models

B:

c:

Summary of Contents for Gen X Series

























Reviews:

No comments