QUICK SETUP GUIDE
QUICK SETUP GUIDE
Thank you for purchasing this Legamaster e-Screen
interactive display. This Quick Setup Guide will help
you setup the monitor and cover the basic operation
instructions.
Please refer to the user manual that can be found on
the USB drive for more detailed instructions and the
full safety and installation information.
Legamaster guarantees the repair or replacement,
free of charge, of faulty e-Screens and/or parts by an
authorized service partner for a warranty period of 5
years. The warranty shall take effect on the date of
purchase as stated on the receipt.
If you wish to make a claim under the warranty or
you have any other service issues, please contact your
dealer or Legamaster directly. Please refer to www.
Legamaster.com/warranty for specific warranty infor-
mation for your market.
This product, when disposed of, is supposed to be
collected and recycled according to your country‘s
legislation to reduce environmental burden.
When you dispose of this product, please contact a
distributor or an affiliate in your country. The contact
addresses are listed on the Legamaster website
http://www.legamaster.com.
By disposing this product correctly you will help
ensure that the waste undergoes the necessary
treatment, recovery and recycling and thus prevent
potential negative effects on the environment and
human health which could otherwise arise due to
inappropriate waste handling.
FCC:
FCC CFR Title 47
part 15 Subpart B.
CB:
IEC62368-1
CE:
EN55032
EN55024
EN61000-3-2
EN61000-3-3
EN62368
CAUTION
MOUNTING OF THIS PRODUCT CAN ONLY BE EXECUTED BY QUALIFIED STAFF
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL
SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER CORD
FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
Item
IR Remote Control (Batteries Included)
Quick Setup-Guide
Power Cable
HDMi Cable
USB Cable
VGA Cable
2 x High precision stylus
USB drive with user manual
Label
Description
Turn the display on and off
Back / return to previous menu
Navigational buttons
Select / confirm (when in menu) or Freeze screen
(when not navigating menu‘s)
Menu
Home
Source selection menu
Volume down
Mute
Volume Up
Adjusting the Volume
1. Using the remote or control panel, press the or
VOLUME- to increase or decrease the volume.
Selecting the input source
1. Press the
SOURCE
button on the control pad. The screen
will display available sources. Select a source by touching
the icon displayed on screen.
2. Using the remote, press the
SOURCE
button and use the
directional arrows to select the desired source.
3. If the display cannot find a source, a “No signal” message
will appear.
Turning the display on
1. Connect the display to an AC power outlet
2. Ensure the AC switch is set to
“|“
.
3. Press the power button on the control pad, alternatively
you can use can use the power button on the remote
control.
Turning the display off
With the Power on, press the power button on the control pad.
A warning message will appear. Alternatively you can use the
power button on the remote control. To turn off power com-
pletely, turn the AC switch to „O“ or disconnect the AC power
cord from the power outlet.
Note:
If there is no signal input for a period of time, the display will automatically go into power saving (sleep) mode.
Control pad table
Volume Up
Volume Down
Settings
Home
Back
Source
On/Off
INTRODUCTION
WARRANTY
RECYCLING INFORMATION
COMPLIANCE
INCLUDED ACCESSORIES
REMOTE CONTROL
TURNING THE DISPLAY ON AND OFF
ADJUSTING THE VOLUME AND INPUT SOURCE
OPERATIONS
IR receiver
+ status LED
Ambient light sensor
16
USB 2.0
17
USB 2.0
CONNECTOR TABLE
17
16
LM-QSG-ETX-5510_GB.indd 5-8
09.05.19 14:34
