3
LA-
1088
4CH amplifier
4 X 75W
4 X 115W
4 X 500W
2 X 500W+1000W
OR
2 X 1000W
2-4 OHMS
4-8 OHMS
40 A
11.38 X 2.48 X 17
(289 X 63 X 432)
9.59 (4.36)
LA-
1488
2CH amplifier
2 X 125W
2 X 200W
2 X 800W
1 X 1600W
2-4 OHMS
4-8 OHMS
30 A
11.38 X 2.48 X 15
(289 X 63 X 381)
8.36 (3.8)
LA-
1888
2CH amplifier
2 X 150W
2 X 225W
2 X 1000W
1 X 2000W
2-4 OHMS
4-8 OHMS
40 A
11.38 X 2.48 X 17
(289 X 63 X 432)
9.46 (4.3)
LA-
2088
2CH amplifier
2 X 200W
2 X 300W
2 X 1200W
1 X 2400W
2-4 OHMS
4-8 OHMS
50 A
11.38 X 2.48 X 19
(289 X 63 X 482)
10.6 (4.82)
Specifications
OUTPUT POWER
RMS @ 4 OHMS
RMS @ 2 OHMS
MAX OUTPUT
BRIDGE MODE
FREQUENCY RESPONSE
INPUT IMPEDANCE
LOW LEVEL INPUTS
HIGH LEVEL INPUTS
INPUT SENSITIVITY
LOW LEVEL INPUTS
HIGH LEVEL INPUTS
POWER SUPPLY VOLTAGE
MATCHING SPEAKER IMPEDANCE
STEREO MODE
BRIDGED MODE
MAXIMUM CURRENT DRAW
DIMENSIONS, W x H x L, inches
(mm)
NET WEIGHT, LBS (KG)
· Phase Control 0-180 degree
· Remote Bass Control
· Input Impedance : 10K Ohms
· Soft Turn On/Off
· Advanced Protection Circuitry
· S/N Ratio:>90dB
LA-
2288
2CH amplifier
2 X 300W
2 X 450W
2 X 2000W
1 X 4000W
2-4 OHMS
4-8 OHMS
70 A
11.38 X 2.48 X 21
(289 X 63 X 532)
11.88 (5.4)
LA-
2488D
Mono channel amplifier
200W mono
335W mono
2000W mono
20-250Hz( 3dB)
10 k-Ohms
100 Ohms
250 mV
4V
14.4 VDC/NEG GD
(10.5-16V)
LA
-488/588/788/988/1488/1888/2088/2288
Features and Controls
LA- 2488D also feature:
1 OHMS
4 OHMS
40 A
11.38 X 2.48 X 13
(289 X 63 X 330)
8.14 (3.7)
Legacy American Amplifier Features
Protection LED Indicator
The protection circuitry in the amp will disable it
if it senses an input overload, speaker short circuit,
or thermal overload conditions. Should this occur,
the PROTECT LED will be illuminated. At that time,
it is important that you check to determine what
has caused the protection circuitry to become
activated.
If the amp shut off because of a thermal overload,
allow it to cool down before attempting to restart.
If the shutdown occured because of an input
overload, or speaker short circuit, be sure to
correct these conditions before attempting to
restart the amp.
To reset the amp, turn the REMOTE power off and
on again.
Power LED Indicator
This LED is illuminated when the REMOTE ON
system is turned on.
11
This unit is provided with gold-plated RCA input
jacks. Using RCA-RCA type patch cords,
connect these inputs to the RCA outputs from
your head unit.
Low Level Input (High Impedance)
10
High Level Input (Low Impedance)
Use these if your car stereo does not have
RCA output jacks: connect the speaker output
from the head unit to these inputs
9
Permits you to adjust the crossover frequency
from 80 Hz to 2.5 kHz to suit the tweeters
High Pass Control
8
Permits you to adjust the crossover frequency
from 35 Hz to 400 Hz to suit the subwoofers
Low Pass Control
7
Allows you to increase the bass signal level sent
to the speakers
Bass Boost Control
6
In a full range system, set this to FULL. If the amp
is being used to power a crossover system, set to
either HPF or LPF as needed.
Crossover Mode Switch
5
Input Level Control
Use this control to match the output of the head
unit to the amplifier. If distortion is present, reduce
the setting of this control.
4
Power Supply Terminals
3
Protects the amplifier as well as the automobile
electrical system from short circuit conditions.
Fuse
2
These terminals are 14K Gold plated for high
conductivity and minimum impedance loss. The
terminals face upwards for easy wiring in tight
situations.
Speaker Terminals
1
12
Plug in the Remote Bass Boost Control wire in here.
13
Remote Bass Boost
specs
Features and Specifications
· Mono Block Subwoofer Amplifier
· 1 Ohm Stable
· MOSFET Power Supply
· PWM (Pulse-Width-Modulation) System
· Glass Epoxy PCB
· Gold Plated RCA Inputs for Line Input & Bypass Output.
· Gold Plated Terminals for Speaker Output and Power Input.
· Thermal, Overload and Short Protection
· Variable Sub-sonic Filter (15Hz~40Hz, 24dB/Octave)
· Variable Low-pass Filter (20Hz~250Hz, 24dB/Octave)
10Hz-30 kHz
10 k-Ohms
100 Ohms
250 mV
2.5V
14.4 VDC/NEG GD (10.5-16V)
