lefeirc SN-L User Manual Download Page 9

                                                                                                                                                                           

SN-L user manual 

 

八、

 

OSD 

 

 

 

 

 

 

* in flight can’t enter the setup menu 

 

Flight summary 

        After the landing, the OSD screen will display the flight summary, and each component will display the maximum value. Restart 

the flight control to eliminate the flight summary. 

 

 

BASE FUNCTION 

       

1.3 AIL BASE FUNCTION 

The default gain can be adapted to most models. 

The heading gain only works in the T-tail type. The V-tail and the delta-wing heading are manually 

controlled, and the flight control does not participate. 

1.4 ELE BASE FUNCTION 

1.5 RUD BASE FUNCTION 

1.1 AIRFRAME TYOE 

T-Tail,    V-Tail,    Wing 

1.2 AP DIRECTION 

0, 180, 90 

1.7 FLIGHT MODE 

 

1.8 WARING BATTARY 

Voltage warning value, OSD will prompt low voltage information 

1.9 AUX 

 

2.0 CALI RC 

Remap RC channel, get cannel range and direction

 

2.1 FAILE-SAFE MODE 

 

2.2 RESET HOME 

updata home location

 

2.4 UNIT 

Switch metric system: “M”/”Ft”; m=”m,m/s, km/h”; Ft=”Ft, Mile, Mile/h” 

2.3 RESET SETTINGS 

Reset all settings

 

1.6 SERVO 

AIL EXP 

Adjust the exp of the RC, the larger the value, the smaller the control amount near the 

center of the joystick; it only takes effect in the MANUAL mode. 

AIL TRIM 

Adjusting the servo offset , can be used to fine tune the rudder surface. 

AIL RANGE 

Adjust the rudder amount of the RC. The smaller the value, the smaller the stroke of the 

joystick control servo. 

 

ADVANCE FUNCTION 

2.1 ADVANCE STAB GAIN 

ALT-HOLD GAIN 

NO NEED 

SPEED GAIN     

In the case of automatic cruising, if the throttle changes in a wave shape, this 

value needs to be reduced. 

FEED-FORWARD GAIN 

The adjustment range is 0~100; the larger the value, the more flexible the 

hand feel, the default is 70. If this value is too large, it will cause the aircraft to 

shake. The small aircraft is recommended to be set to around 35-45. 

SPEED PID FACTOR 

Reduce the effect of speed on servo sensitivity

 

2.2 CONTROL RATE 

Control the rotation speed of the aircraft's roll and pitch. The larger the value, the more flexible the aircraft, 

and the larger the wingspan can be set larger. 

2.3 MAX ROLL ANGLE 

 

Enter OSD menu 

Flip mode switch twice 

AIL move left 

Exit the current menu or exit the selected mode 

AIL move right 

Enter menu or select setting item 

ELE move up or down 

Change item index or select parameter 

Summary of Contents for SN-L












Reviews: