Garden socket – Installation instructions
Figure 1
Subject to mechanical modifications.
07/2020
LEDs Com GmbH, Dohrweg 2a, D-41066 Mönchengladbach, www.ledscom.de, Tel. +49 (0) 21 61-5 75 99 76
Protection against foreign
bodies larger than 1 mm Ø,
protection against spray water
IP44
Connection box
1
Strain relief
3
Screws
2
Switching pins
I
Programming disk
II
Override switch
III
Marking arrow
IV
Status indicator
V
Product number
Operating voltage
Protection class
Protection type
No. of sockets
LC-SS-903
230 volts 50-60 Hz
IP44
3
1
2
3
Figure 2
Figure 3
Green/Yellow
Blue
Brown
N
L
Protection class 1: all
electroconductive frame
components are grounded.
I
II
III
IV
V
Please read these installation instructions
carefully before installing this light and keep it
for future reference.
1. Safety instructions
The installation of the light may only be performed by a trained
electrician.
Only operate this product, if it works correctly. In the event of a
fault, do not touch the product. Switch off the product immedi-
ately by an external switch. Touching the product or continuing
its operation in the event of a fault results in danger to life due
to burn, electrical shock or fire.
How to detect a fault:
• the product does not work correctly (e.g. flickering of the lamp,
cannot be switched on)
• the product smokes, crackles or smells burnt
• the product overheats (discolouration, even on the adjacent
areas)
Operate the product again only after repair and testing exclusi-
vely by a trained electrician.
2. Intended Use
This lamp may:
• only be operated at a voltage of 230V ~50 Hz.
• only be connected according to protection class I (one).
• only be used according to protection rating IP44.
• not be operated by means of a dimmer.
• only be operated if mounted firmly on a robust, flat bottom.
• not be exposed to strong mechanical stress.
• not be changed or modified.
The product is not intended for use by children. Make sure that
the product does not cause any damage to children, e.g. burn by
hot surfaces, electrical shock.
If the lamp is not used in accordance with these requirements,
especially if moisture enters the lamp, it results in danger to life
due to burn, electrical shock or fire.
3. Maintenance and care
The following environmental influences can have undesirable
effects on the surface of the product:
• acid rain or soil, high salinity of the air
• cleaning agents
• other chemical substances (e.g. mold remover)
Protect the product by appropriate measures to avoid changes
to the surface.
First disconnect the whole product from the power supply and
let it cool down before cleaning and care. Clean the product
regularly – only by a slightly moistened, soft, lint-free cloth.
4. Storage
• The product has to be stored under dry conditions, protected
against contamination and mechanical impact.
• After a humid or contaminated storage the product has to be
tested by a trained electrician before operating.
5. Disposal (European Union)
• The product must not be disposed of with the household
waste. Products marked with this symbol have to be
disposed of under the terms of the EU Waste Electrical and
Electronic Equipment (WEEE, 2012/19/EU) Directive by
local return centres.
6. Installation instructions
(Figure 1)
1. Disconnect the mains lead of the building by disconnecting
the building wiring fuse and protect it against reconnection.
2. pull the connection box (1) out of the garden socket. Loosen
the four screws (2) and remove the cover of the connection
box (1). Loosen the strain relief (3).
3. Connect the connection cable on the building side to the lus
-
ter terminal inside the junction box (1) as shown in Figure 2.
4. Fix the connection cable with the strain relief (3) and close the
connection box (1). Tighten the screws (2) firmly by hand.
5. Mount the socket column on solid ground or with a ground
spike using the screws and dowels provided.
6. Switch the power supply on again. The installation is now
complete.
Operating the mechanical timer
(Figure 3)
The timer is set via the green switching pins (I) on the edge of
the programming wheel (one switching pin equals 15 minutes)
Programming wheel (II):
The time is set by turning the programming wheel clockwise un-
til the current time matches with the marking arrow (IV) on the
disk.
Override switch (III):
Position I: manual switch on
Position clock symbol: programmed switching on and off.
Status indicator(V):
The display indicates whether the sockets are switched on or off.
