Rev. May-21
Million Color SMD LED Slimline RV Underbody Kit
Warning:
Please check your state and local laws before installing this Million Color SMD LED Slimline RV Underbody Kit. Every state has
different policies and procedures in place regarding aftermarket vehicle accessories. LEDGlow is not responsible for any fines that you may
receive while using this underbody kit. This kit is for off road use only.
Warning:
We recommend using a licensed professional to install this kit. The improper installation of this kit will void all warranties.
The control box that powers the underbody tubes must be installed in a dry location inside of the vehicle. Having this part exposed to water
or the elements will cause the kit’s controller to fail. Any water damage or corrosion to this part will VOID all warranties.
PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING AND OPERATING THIS UNDERBODY KIT.
RV Underbody Kit Includes:
(
Quantity for parts will vary depending on the kit you
have.)
•
24 Inch Tubes
(45 Individual LEDs)
•
36 Inch Tubes
(60 Individual LEDs)
•
46 Inch Tubes
(90 Individual LEDs)
•
Control Box
•
Wireless Remote
•
Connection Hub
•
Cable Extension
•
Connector Endcap
•
Underbody Tube Brackets
•
Zip Ties
•
Screws
RV Underbody Kit Installation:
1.
This kit is designed to be expandable, and you can add onto the system using
Connection Hubs. Each Connection Hub is designed to hold a max of 8)
46” tubes
,
which is 720 individual LEDs. If you are using smaller tubes, you can connect more
tubes if you do not exceed the 720 individual LED count.
2.
Temporarily power your kit with any 12-volt source and test for full functionality before
you move forward with the installation. Simply connect the red wires from the Control
Box and Connection Hubs
to the positive terminal on the vehicle’s battery and the black
wires from the Control Box and Connection Hubs to any reliable ground source. Power
the kit and test all the colors and modes. If everything is good, remove power.
3.
Be extremely aware of the location of the brake lines and fuel lines and do not mount
any of the underbody tubes too close to the location of any fold down steps,
compartments that open, slide outs, exhaust from the engine or generator, and any other potential obstructions. Leave at least 8
inches between the exhaust and the underbody tubes. Keep the tubes and the power wires away from any moving parts.
•
When arranging the tubes around the RV lay the longer 46” tubes out first looking under the RV for potential mounting
locations. Different obstructions will play a big part in the configuration of short and long tubes. Plan to have a shorter
24” tube next to the stairs on either side as the width of the stairs will take away some area where you can safely mount
lighting.
•
Keep in mind the configuration of the tubes may be different from the left and right sides of the RV.
•
Due to the width of your RV, you should be able to mount 2)
36” tubes in both the front and the rear. Keep in mind any
obstructions that could distort the light as well as moving parts and heat and avoid these areas.
Note:
3 brackets are provided for each tube: one for each end of the tubes and one for the center of the tubes.
•
If you have a location where the bracket will not fit or cannot be mounted, we recommend using wire ties and attaching
to a conduit or a bracket that is already in place.
4.
When you are laying out the tubes and determining the Control Box and Connection Hub
locations, keep in mind that you can connect 2 hubs directly off of the Control Box to create
zones. For instance, you can utilize the driver side and passenger side, front and rear, or any
other locations that best suit your installation.
•
Attach the male connector coming from one of the harnesses on the bottom of
the Controller to the female connector coming from the left of the Connection
Hub.
•
Attach the male connector coming from one of the harnesses on the bottom of
the Connection Hub to the female connector of the light tube. Then daisy chain
the rest of the tubes. Be sure to evenly split the tube count between the two
harnesses when possible, Max is 360 individual LED
’
s per harness.
