background image

4/4

IMPORTANT !

 

Wrong!

4"

(100mm)

On widest one flat plane (only)

Do not bend sideways. 

Flexible on one axis

maximum band radius 4”

1

2

3

Apply heat with heat gun to seal 
connection. Wire jacket must be 
covered by Heat shrink (1/4"") and PVC 
cover must be 1/2". RTV Electronics 
grade silicone glue to seal.

0.50"

1 ½”long, 3/8” Wide electrical heat 
shrink. Note Fig 1. is showing is 2 wire 
for single color FlexStrip. RGB FlexStrip 
will have 4 wires. Use only RTV 
Electronics grade silicone glue over 
connections to seal.

Solder wires and place end cap over 
wire as in Fig.2. End cap must also be 
sealed with heat shrink.

The following task requires personnel experienced with soldering and low voltage DC wiring techniques. 

Note : End cap is included in each light kit along with mounting clips. If product is cut, it is no longer water resistant (IP-22)

TROUBLESHOOTING 

Tape light strip does not light

Ÿ

Make sure your power supply is turned on and has the correct voltage.

Ÿ

Conrm you have the correct polarity (+ to + and - and -) throughout the run of LED Lighting.

Ÿ

Have a electrician check all connections and any switch or dimmer connections from the power supply to the LED Light Strips.

Ÿ

Consider testing with a multimeter to ensure light strip is receiving 12V power. 

LED Flex Strip lights blink on, then go off

Ÿ

The power supply is not adequate for the length of LED Light Strips you are powering. Install a adequate Class 2 power supply.

LEDs farthest from the power supply are noticeably dimmer

Ÿ

This is the result of voltage drop. Decrease the length of the 12V power feed or use thicker power feed wires between the 12V power supply 
and the lighting strips.

IMPORTANT INSTRUCTIONS

MAXIMUM FLEXSTRIP LENGTH SUPPORTED BY LED WORLD’s CLASS 2 POWER SUPPLY

Power Supply

Max Feet of LED Flexstrips

Power Supply

Max Feet of LED Flexstrips

XLD75B-112V-FC

27.2 Feet (Continuous 60 Watts)

XLD200B-412V-FC

4 X 18 Feet (Each Channel)
Total 72 Feet

YHY-12005000

22 Feet (Continuous 48 Watts)

CVN50L12DC

18.18 Feet (Continuous 40 Watts)

RGB LED FLEX STRIP

  

 

Model

: FC30M50-5M-12V-RGB (RGB: Red, Green, Blue)

1-800-387-4081

 

ledworldlighting.com ledworld.ca

 | 

 

Copyright © 2019 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).

LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 4.0 - 09/18/19

Summary of Contents for FC30M50-5M-12V-RGB

Page 1: ...ineer can perform installation familiar with low voltage wiring techniques Correct polarity is imperative is marked on printed circuit Parallel connection only Ÿ DO NOT install on ammable material or possibility of in the future Do not install any luminaire closer than 6 inches 15 25 cm from any curtain or similar combustible materials Ÿ The light and all its components cannot be mechanically pres...

Page 2: ...starting the installation process General questions based on lighting requirements Ÿ Where will your power supply be located Ÿ How will you switch your LED lighting ON and OFF Ÿ What is the best layout con guration for your installation with wiring consideration Ÿ How will you run your wiring to your LED strip lighting WATTAGE CALCULATION The LED Flex Strips have a label on each roll that indicate...

Page 3: ...2W LAYOUT OPTIONS Note Always check the Wattage of your LED Strip or Fixture Power Supply Wattage x 0 8 Available Wattage Class 2 Power Supply 60W Class 2 Power Supply 60W Layout 1 22W 22W 30W 30W Available 48W Available 48W Layout with Overload Do Not Use Securely mount wires using wire clamps AC120V 40W 40W 40W 50W 50W 50W 50W RGB LED FLEX STRIP Model FC30M50 5M 12V RGB RGB Red Green Blue 1 800 ...

Page 4: ...ns from the power supply to the LED Light Strips Ÿ Consider testing with a multimeter to ensure light strip is receiving 12V power LED Flex Strip lights blink on then go off Ÿ The power supply is not adequate for the length of LED Light Strips you are powering Install a adequate Class 2 power supply LEDs farthest from the power supply are noticeably dimmer Ÿ This is the result of voltage drop Decr...

Reviews: