Lectrosonics UM 200C Operating Instructions Manual Download Page 2

Page: 2 / 16

UM200C

LECTROSONICS, INC.

TABLE OF CONTENTS

The UM200C transmitter is FCC type accepted under Part 74: 470-608MHz and 614-802MHz

INTRODUCTION .................................................................................................. 3

GENERAL TECHNICAL DESCRIPTION ............................................................ 4

CONTROLS AND FUNCTIONS .......................................................................... 6

BATTERY INSTALLATION ................................................................................... 8

OPERATING INSTRUCTIONS ............................................................................ 8

OPERATING NOTES ........................................................................................... 9

ADJUSTING THE TRANSMITTER FREQUENCY .............................................. 9

MICROPHONE CORD TERMINATION ............................................................. 10

5-PIN INPUT JACK WIRING .............................................................................. 11

TROUBLESHOOTING ......................................................................................... 14

SPECIFICATIONS AND FEATURES ................................................................. 15

SERVICE AND REPAIR ...................................................................................... 16

RETURNING UNITS FOR REPAIR .................................................................... 16

WARRANTY .......................................................................................... Back cover

Summary of Contents for UM 200C
















