background image

HH

LECTROSONICS, INC.

14

Specifications

The FCC requires that the following statements be included in this manual:

This device complies with FCC radiation exposure limits as set forth for an uncontrolled 

environment. This device should be installed and operated so that its antenna(s) are not 
co-located or operating in conjunction with any other antenna or transmitter.

Operating frequencies:

Block 470  470.100 - 495.600 

Block 19 

486.400 - 511.900 

Block 20 

512.000 - 537.500 

Block 21 

537.600 - 563.100 

Block 22 

563.200 - 588.700 

Block 23 

588.800 - 614.300 

Block 24 

614.400 - 639.900 

Block 25 

640.000 - 665.500 

Block 26 

665.600 - 691.100

Frequency selection: 

 

 

(Normal Tuning mode); 

256 frequencies in 100 kHz steps 

 

(Fine Tuning mode) 

1024 frequencies in 25 kHz steps 

 

(except block 23 - contact Lectrosonics for details)

Channel Step Size: 

 

Normal Tuning mode: 

100 kHz 

 

Fine Tuning mode: 

25 kHz

RF Power output: 

Selectable at 50 or 100 mW

Pilot tone: 

25 to 32 kHz frequency - 5 kHz deviation 

 

 

(Hybrid, IFB, 200 Series, Mode 6)

Frequency stability: 

± 0.002%

Deviation: 

± 75 kHz max. (Digital Hybrid mode)

Spurious radiation: 

90 dB below carrier

Operating temperature range: 

-30° C to +60° C

Input compressor: 

Dual envelope compressor, >30 dB range

Audio Gain range: 

0 to 45 dB; menu selectable

Modulation indicators: 

Dual bicolor LEDs indicate modulation  

 

 

of -20, -10, 0 and +10 dB referenced to full  

 

 

modulation, LCD bar-graph indicator

Frequency response 

40 Hz to 20 kHz (+/- 1dB)

Low frequency roll-off: 

-3 dB selectable @35, 50, 70, 100, 125 Hz, 

 

 

36 dB/octave (varies slightly w/ selection)

Controls: 

 

External: 

Programmable mute/talkback button 

 

Internal control panel: 

Power, Side Button Setup, MENU/SEL, BACK 

 

 

and Up/Down arrow buttons for menu item 

 

 

selection and settings.

Battery: 

(2) AA with polarity protection and 

 

 

battery ejection lever

Battery Life: 

5.5 hours (alkaline); 8-10 hours (lithium)

Battery Status Indication: 

Transmitted to Lectrosonics Digital Hybrid and 

 

 

200 Series receivers

Capsule Interface: 

1.25 in. diameter x 28 thread pitch

Capsule Power available: 

5V, 25 mA max

Input impedance: 

1000 Ohms

Weight: 

11.4 oz. with lithium batteries and HHC 

  

capsule

Dimensions: 

9.5” long x 1.97” diameter at largest point with 

 

 

HHC capsule attached 

Emission Designator: 

180KF3E

† Not all frequency blocks are available in all countries. Consult your local 

representative or contact Lectrosonics for more information.

Specifications subject to change without notice.

Summary of Contents for Handheld Transmitter

















Reviews: