Lectronics VR Field Reference Manual Download Page 29

Page: 29 / 32

Modular Digital Hybrid Wireless™ Receiver

Rio Rancho, NM

Symptom

Solution

Bad.frequency.response.or.generally.poor.audio.quality
. .

Ensure the Receiver Module is set to the Compatibility Mode

matching the associated transmitter.

Check for Intermodulation problems. (See Frequency Coordination.)

Note: A number of symptoms may be caused by a strong interfering signal on the same frequency. Use the VR Field

System’s Scan function to verify the transmitter and receiver are operating on a clear frequency channel.

Computer.Interface.Problems

“New.Hardware.Found”.message.does.not.appear.when.USB.cable.plugged.into.VR.Field.System
. .

Defective USB cable between Computer System and VR Field, or

between Computer System and USB Hub (Multiple System

Configuration).

Defective USB Hub (Multiple System Configuration)

VRpanel software installed, but USB Driver not installed. (See

Installing LecNet2

™

Software and USB Driver.)

VRpanel.detected.by.Windows.but.cannot.be.detected.by.VRpanel.program
. .

VRpanel software installed, but USB Driver not installed. (See

Installing LecNet2

™

Software and USB Driver.)

Not.all.VR.Field.Systems.appear.in.response.to.the.“Add.VR(s).via.USB...”.command
. .

Defective USB cable between USB Hub and affected VR Field System.

Defective USB Hub.

Summary of Contents for VR Field

































Search results

Summary of Contents for VR Field

Reviews:

Related manuals for VR Field

Brands by name

Popular brands

Lectronics VR Field, Reference Manual

Search results

Summary of Contents for VR Field

Reviews:

Related manuals for VR Field

Brands by name

Popular brands