Working logic
“Step-by-Step” logic (Dip 1 = OFF Dip 2 = ON)
A
Start
control puts into motion, a following control stops the motion, a further
Start
control reverses the motion (direction reverse).
“Automatic closing” (Dip 1 = ON Dip 2 = ON)
When the gate has reached opening it will automatically close after the set
Pause time
. A
Start
control supplied during the pause interrupts work
cycle and the gate doesn’t close automatically.
Photocell
intervention during pause time reloads it, extending the period before automatic closing.
“Condominium” logic (Dip 1 = not influent Dip 2 = OFF Dip 3 = not influent)
When the gate has reached opening it will automatically close after the set
Pause time
. A
Start
control supplied while opening is not influent.
A
Start
control supplied while closing provokes the stop and gear reverse after approx.
1,5 sec
.. A
Start
control or
Photocell
intervention during
pause time reloads it, extending the period before automatic closing.
WARNING:
after each modification of the working logic, switch the control unit off and on again to make the change active.
“Immediate closing” (DP3=ON DP2=ON)
In opening phase and during pause time, after having passed the
Photocell
, it determines the stop and, after
1,5 sec
., gate closing.
Programming
Learning of remote controls
To enter a
Start
code, press the
P1
key once. To enter a
Pedestrian start
code, press the
P1
key twice. Each time the
P1
key is pressed, the
DL1
led
emits a short flash. After
3 seconds
from the last pressure of
P1
, the
DL1
led turns on with a steady light. Then press the key to be memorized on the
remote control. The
DL1
led will switch off, indicating that the code has been memorized. If the code is not recognized, the
DL1
led stays on for
10 sec., after which it will automatically switch off
.
Erasing of all memorized codes
To delete all the stored codes, keep the
P1
key pressed for approx.
10 sec.
until the
DL1
led turns off.
Setting of pause time
To set the
pause time
, press the
P2
key once.
DL1
led emits a short flash and, after
3 sec
., turns on with a steady light. Let pass the time
corresponding to the desired time and press again the key
P2
.
Programming of work time
Make sure the gate is completely opened. Press button
P3
for approx.
3 sec.
until
DL1
led turns on with steady light and the gate start to close.
Wait for the gate to reach the
closing limit switch
. The gate stops and the Led
DL1
switches off, signalling the end of the programming.
The program automatically computes the point of slowing down start (
1/8 of stroke
). To modify it, while programming press the key
P3
in the
wished point during closing step.
Technical data
Card dimensions and weight
: 170 x 70 x 45 mm – 0,14 Kg
Card power supply (Vin)
: 20
Vac
Stand-by power consumption
: approx. 1
W
Operating temperature range
: 0 to + 60 °C
Brushless motor power supply
: 24
Vdc
Blinker power supply (LED)
: 12
V 3
W max.
Accessories power supply
: 12
Vdc 3
W max.
Pause time regulation
: 1 to 300 sec. %
DECLARATION OF CONFORMITY
Device description:
Electronic board controlling a 24
Vdc Brushless motor destined to sliding gate automation.
Model:
CTR640
Applied rules:
EN 61000-6-3, EN 61000-6-1, EN 301489-1, EN 301489-3, EN 300220-2, EN 300220-1, EN 60950-1
Test laboratory:
NEMKO SPA
The manufacturer declares that above mentioned products comply with rules required by European directives
2004/108/EC
and
2006/95/EC
.
Date: 15-07-2020
CONNECTIONS
+
Receiver
DS1
DS1
1
2 3
ON
OFF
