background image

Lear UGDO 

Lear UGDO Owner’s Guide Version 3.2  Page 6 

3/27/2006 

Programming Fixed Code Garage Door Opener or Device 

Make sure that your key is ON and engine OFF while programming the transmitter.  Use the 
following steps to program up to three different devices.  

1. To

program a fixed code garage door opener you

 will need the garage door hand-held 

transmitter and a paper and pen or pencil. Between 8 and 12 coding switches are revealed 
under the battery cover of the hand-held transmitter.  

Do not

 change the switch positions.

2. Write down the switch settings from left to right.   When a switch is in the Up position, 

write “on”, and when a switch is in the Down position write “off”.  If a switch is set to a 
third position between the Up and Down, write “middle”.  An example is shown here.  

O

N

1

2

3

4

5

6

7

8

Switch 

Number 1 2 3 4 5 6 7 8 

Switch Position On On Off On  Off  On  Off Off

3. Input these Positions into the Car2U as follows.  Simultaneously Press and Release all 

three Car2U Buttons to put the device into programming mode.  

4.  The indicator lights will blink slowly.   In order from left to right, and within 2.5 

minutes, enter each switch setting into Car2U.  Push one Button for each switch as 
follows: 

ƒ

Left Button =  “On” switch position 

ƒ

Right Button = “Off” switch position  

ƒ

Middle Button = “Middle” switch position 

Short Term Confidentiality Requested

Summary of Contents for UGDO









Reviews: