http://www.leadsun.com.cn
2
AE2 solar lights absorb energy from our sun and turn it into area illumination when it is dark. Their
integrated photo voltaic module, micro controller and lithium battery combine with high output LEDs
and a human infrared sensor to achieve multiple features such as low power consumption with high
luminance. Their design delivers a long lifespan with minimal maintenance and provides a complete
solution for off-grid or remote applications. IP65 rated components ensure endurance against harsh
weather and keep AE2 solar lights free from corrosion and premature failure. Leadsun wishes your
enjoyment of this highly innovative product and thanks you for helping conserve this planet's
resources by using products that reduce the consumption of earths resources.
To avoid incorrect operation that may lead to damage the unit, please read
the following instructions for AE2 solar lights carefully before installation.
AE2 units do not work without sunlight. Please choose the appropriate model according to irradiance
or peak sun hours for the location of the installation. In areas that are short of sunlight or after
continuous days of rain, AE2 units may only work shortly or may not turn on at all. For areas where
this applies we recommend the use of the AC input capable models.
AE2 units incorporate highly efficient lithium batteries.
The functional charging temperature range is
0~+60
℃
.
The controller will stop charging automatically in order to protect battery when
(
32
℉
~140
℉)
temperature is lower than 0
℃
or higher than 60
℃(
. And it will commence charging when
(
32
℉)
140
℉)
temperature returns to the range between 0
℃
and 60
℃(
. The discharge temperature
(
32
℉)
140
℉)
range is -20~+60
℃
-4
.
( ℉
~140
℉)
Please make sure that the maximum temperature of the location
installed does not exceed the above range.
AE2 units can be stored with full charge for a maximum of 6 months. It will be necessarry to check
charge and make records regularly during long periods of storage or the battery may be damaged.
AE2 units should be installed with the solar panel facing the equator for best performance and
durability. Make sure to clear trees, buildings and other shadows or the internal battery will not charge
properly and the efficiency of the solar panel will be minimized, influencing the working time of the unit
and battery life.
Cleanliness of AE2 units solar panels affects their generating efficiency. It is necessary to regularly
clean the surface of the solar panel in areas with a high volume of dust or tree residue.
All internal parts of AE2 units are rated lP65 and are waterproof. Holes and slits on the luminaries are
designed for heat dissipation and drainage. Metal parts are anodized rust-proof aluminum or stainless
steel which can withstand high temperatures and high humidity in coastal or desert areas. The anti-
theft designs of the fastening brackets add security to AE2 units.
30%
Dim mode
100%
Bright mode
AE2 works at dim mode when humans are not around and it will increase light output immediately when motion is detected.
5
Please open the package and confirm that all parts were received prior to installation. Refer to figure 1.
It is important to install the lamp post in a position that will allow the luminaries exposure to direct
sunlight. As a suggestion, the pole height should be 3 to 5 meters, pole diameter should be 60-90 mm,
and lamp post thickness whether steel or iron should be more than 2mm thick.
Connect the waterproof wire terminal cap in the bracket, fasten the screws, and then put the terminals
back into the bracket to avoid damage while installing onto the pole. Refer to figure 2.
For ideal installation of models with AC input, it is advised that you pre-plan the position of the luminaries
on the pole. Port holes through the pole and insert the wire through for a clean installation. Please have a
licensed electrician install this unit to avoid risk of failure, damage to luminaries and to minimize the risk
of shock. Cable polarity is as follows: L (red), N (blue), G (yellow/green). Finalize wiring with silicone to
waterproof after soldering or crimping.
AE2 luminaries have security fasteners integrated in the mounting bracket. A special tool has been
provided to fasten the bolts. The maximum torque for these M8 bolts is about 12Nm. Do not surpass this
torque specification.
Installation Guide:
Assembly parts ( Figure 1 )
Connect the waterproof wire terminal cap. ( Figure 2 )
Solar module
Brackets
M8 burglarproof bolts
Fastening tool
Nut
Spring washer
3
AE2 User Manual
