Leader I40.90.110 User Manual Download Page 18

 

18 

 

12

 

WARRANTY 

 

LEADER

 equipment benefits from a limited contractual warranty from the date of the purchase, 2 years parts and labour 

(excluding shipping and travelling fees). Normal wear parts are excluded from this warranty. 
 
This warranty is specifically limited to replacing or repairing the equipment (or its parts) which after examination proves to 
be defective for causes attributable to 

LEADER

.  

To claim under a warranty, the user (with 

LEADER

’S approval) will need to return the equipment to 

LEADER

, ZI des 

Hautes Vallées, Chemin n° 34, CS 20014, 76930 Octeville Sur Mer, France as soon as possible following the discovery of 
the defect. 
 
 
 
After reviewing the equipment: 
 

If the defect is attributable to 

LEADER

, it will repair it and assume the costs (excluding shipping and travelling fees), 

If the defect is not attributable to 

LEADER

, see the procedures laid down in the out-of-warranty Defect paragraph. 

 
 
This warranty does not commit 

LEADER

 in the following cases: failures resulting from improper handling, improper use 

of  the  equipment,  no  maintenance  or  incorrect  maintenance,  incident  affecting  the  hardware,  repair  or  modification  by 
another company or non-authorised personnel.  
 
 

OUT-OF-WARRANTY DEFECT OR EQUIPMENT NO LONGER COVERED BY THE WARRANTY  

 
A complete diagnostic will be conducted on your defective equipment, at the end of which a detailed estimate will be sent 
to you for the necessary repairs. 
For  failures  and  repairs  no  longer  covered  by  the  warranty,  a  diagnostic  flat  rate  will  be  applied  regardless  of  the 
acceptance of the repair quote. 

 

 

 

 

 

 

 

 

 

Summary of Contents for I40.90.110





















Reviews: