background image

*29268*

29268

 

The 4600CS Series electric Auto-Equalizer™ series combines all door 

operator and door control functions in one package. This versatile, 

easy-to-install system is low maintenance and offers the following 

features: 

•  Top jamb mounting on either side of an interior door allows 90° 

of power opening. (Mounting for exterior door on the inside only)

•  Manual opening up to 170° (4630CS) or 100° (4640CS).
•  Quiet, reliable operator delivers consistent performance.
•  No expensive service contracts or periodic maintenance 

required.

•  Fail safe operator acts as a standard door closer in event of 

power outage.

•  Low energy operator does not require guard rails or safety mats.
•  Advanced, easy-to-install controller module allows independent 

adjustment of:
a.  Door Opening Speed
b.  Delay / Trigger Time for Sequential Option
c.  Door Opening Force
d.  Electric Strike Delay Time
e.  Hold Open Time
f.  90° Slow Down
g.  Alternate Action Timeout
h.  Safety Scanner Lockout Time

Table of Contents

Pg. 2 .......... General Information
Pg. 3 .......... Install Mounting Plate
Pg. 4 .......... 4630CS Template
Pg. 5 .......... 4640CS Template
Pg. 6 .......... Installing Closer Assembly
Pg.7-8......... 4600CS Series Arm Installation
Pg. 9 .......... Closer Regulation & Power Adjustment
Pg. 10 ........ Controller Installation
Pg. 11 ........ Electrical Connections
Pg.12-13..... Typical Wiring
Pg.14 ......... Auxiliary Electrical Device Wiring
Pg.15 ......... Controller Setting Adjustment
Pg. 16-17.... Controller Programming
Pg.18 ......... Basic Operation & Cover Installation
Pg.19 ......... Illustrated Parts List

4630CS, 4640CS Electric Auto Equalizer Series

4600CS Electronic Low 

Energy Operator

Installation Instructions

Customer Service

1-877-671-7011

www.allegion.com/us

4640CS

PUSH SIDE MOUNT

4630CS

PULL SIDE MOUNT

Summary of Contents for 4600CS






















Reviews: