Assembly Instruction
2 SETS
#1
#4
#3
#2
A
B
C
Parts List
SEAT FRAME
BACK FRAME
WRENCH
Hardware List
Bolt+SPRING FLAT WASHER--5/16" Dia
4 SETS
1 PC
2 PCS
7 PCS
3" L
QTY
QTY
1-1/2" L
Bolt+SPRING FLAT WASHER--5/16" Dia
2-1/2" L
Bolt+SPRING FLAT WASHER--5/16" Dia
4 SETS
1 PC
FRONT LEG
NO.
1 PC
#5
WOOD SCREW
D
CUSHION
1 PC
THANK YOU FOR PURCHASING THIS QUALITY PRODUCT. BE SURE TO CHECK ALL PACKING MATERIAL CAREFULLY FOR SMALL
PARTS THAT MAY HAVE COME LOOSE INSIDE THE CARTON DURING SHIPMENT.
CAUTION: (1) THESE PARTS ARE CUMBERSOME AND HEAVY. THIS PRODUCT CAN BEST BE ASSEMBLED WITH THE ASSISTANCE OF
ONE OR MORE PERSONS IN ORDER TO PREVENT PERSONAL INJURY AND TO INSURE PARTS ARE NOT DAMAGED DURING THE
ASSEMBLY PROCESS. IF DIRTY, CLEAN FINISHED PARTS WITH MILD DISHWASHING LIQUID AND WATER SOLUTION APPLIED ON
DAMP CLOTH. CLOTH SHOULD NOT BE EXCESSIVELY WET. POLISH FINISH WITH SOFT CLOTH AND AN INDUSTRY RECOGNIZED
FURNITURE POLISH.
(2) TO PREVENT DAMAGE TO YOUR FLOOR OR CARPET, PLEASE CHECK THE BOTTOM OF EACH PIECE OF FURNITURE FOR
STAIN RESIDUE AND ROUGH SURFACES AND ALSO CHECK FOR STAPLES OR NAILS LEFT AFTER REMOVING THE PACKAGING
MATERIAL. THE MANUFACTURER WILL NOT BE HELD RESPONSIBLE IF PREVENTATIVE STEPS ARE NOT TAKEN PRIOR TO
INSTALLATION.
(3) UNPACK AND DISPOSE OF ALL PACKING MATERIAL BUT BE CAREFUL NOT TO THROW AWAY ANY ASSEMBLY PARTS
OR HARDWARE. READ THE INSTRUCTION SHEET AND PARTS LIST CAREFULLY. REMOVE ALL STAPLES AND SCREWS USED FOR
PACKAGING CAREFULLY USING PLIERS AND OR SCREWDRIVERS TO PREVENT INJURY AND SCRATCHING OR DAMAGING
FLOORING.
(4) DURING NORMAL USE EVERYDAY, SCREWS, BOLTS, NUTS AND WOODEN PLUGS MAY LOOSEN UP. THEY SHOULD BE
PERIODICALLY INSPECTED AND RE-TIGHTENED TO PREVENT DAMAGE TO THE FURNITURE AND (OR) PERSONAL PROPERTY OR
CAUSE INJURY. ALWAYS CHECK TO BE SURE ALL HARDWARE ON THIS LIST AND THE ABOVE MENTIONED COMPONENTS IS
ATTACHED TO THE FURNITURE PROPERLY AND KEPT TIGHTENED AT ALL TIMES.
Parts and Hardware List:
IMPORTANT NOTE:
1.USE ONLY THE HARDWARE SUPPLIED.
2.DO NOT OVER-TIGHTEN BOLTS
3.FIRST READ THE CHAIR LEVELING INSTRUCTION SHEET.
ASSEMBLY INSTRUCTIONS:
STEPS
1. PLACE THE
CUSHION
(B)
UPSIDE DOWN ON A CLEAN, SOFT SURFACE. ASSEMBLE THE SEAT FRAME
(
A
)
TO CUSHION
(B)
USING
SCREW
(4).
2. REMOVE THE PLASTIC COVER ON THE UPHOLSTERED SEAT
. ASSEMBLE THE
BACK FRAME
(C)
TO THE BACK RAIL OF THE SEAT
FRAME
(A)
USING -----
# 1
(BOLT + SPRING FLAT WASHER).
3.
ATTACH THE REAR CORNER BLOCKS OF THE SEAT FRAME
(A)
TO THE BACK LEGS AND FRAME
(C)
USING -----
# 2
(BOLT+
SPRING FLAT WASHER).
4. ASSEMBLE FRONT CORNER BLOCKS OF SEAT FRAME WITH THE FRONT LEGS
(D)
USING -----
# 3
( BOLT + SPRING FLAT
WASHER ). HAND TIGHTEN THESE BOLTS WITH WRENCH
# 5
.
5. AFTER MAKING SURE ALL BOLTS ARE ATTACHED AND HAND TIGHTENED, TURN THE CHAIR OVER.
6 . LEVEL THE CHAIR FOLLOWING “CHAIR LEVELING INSTRUCTION” .
7. MAKE SURE THE CHAIR IS LEVEL AND THEN TIGHTEN ALL BOLTS COMPLETELY USING THE WRENCH SUPPLIED.
