LC Packings Probot 161403 User Manual Download Page 85

Page: 85 / 118

User’s Manual Probot

D960R3

A-1

APPENDIX A

Dosage Module Purge Routine

A.1

Overview

The dosage module (optional) is provided to add a reagent solvent (e.g. a matrix

solution) to the mobile phase flow. The figures presented below are provided to

describe the step-by-step procedure of how to remove air from the syringe and

how to purge the dosage module. For a detailed description of the software
control of the dosage module, refer to the

Carrier software user’s manual.

Note: All fluidics pathways of the dosage module (e.g. the rotary valve, the

syringe and all tubing) must be free of any air bubbles and must be properly

purged.

A.1.1

The Step-By-Step Purge Routine

(FIGURE 2-5, Page 2-10) presents the dosage module with the syringe installed

in the syringe drive. FIGURE A-1 presents a schematic of this normal

configuration.

Wast

Aux

)

Reagent

Vials

Syringe Pump

Dosage Module

PUMP

FILL

PURGE

Pump

Fill

Rotary Valve

Needle
Tee

µ-Tee

AUX

a) Wash Solvent

FIGURE A-1 Normal Configuration of the Dosage Module

Summary of Contents for Probot 161403























































































































Search results

Summary of Contents for Probot 161403

Reviews:

Related manuals for Probot 161403

Brands by name

Popular brands

LC Packings Probot 161403, User Manual

Search results

Summary of Contents for Probot 161403

Reviews:

Related manuals for Probot 161403

Brands by name

Popular brands