LC Packings Probot 161403 User Manual Download Page 114

Page: 114 / 118

Appendix E

E-2

D960R3

User’s Manual Probot

E.2

Software Installation and µCarrier Setup

The following section describes how to install the drivers for the support of the

Belkin USB video adapter. The necessary drivers are provided with the µCarrier

V2.0 CD ROM and can be copied onto your hard disk using the installation

program of µCarrier. To download the latest drivers or in the case that the

µCarrier CD is not available, visit the Belkin home page

www.belkin.com

and

search for ‘F5U208’.

Note: Do not connect the Belkin F5U208 VideoBusII Image Capture Device until

the installation software prompts you to do so!

To install the drivers for the Belkin F5U208 USB VideoBusII Image Capture

Device:

Locate the directory (default name: C:\F5U208) with the unzipped files which

was created during the µCarrier installation (if this option was selected during

installation) and continue with step c).

If the files were not copied to the hard disk, copy the files as discussed in

Section 2.5 or download the appropriate drivers from ‘

www.belkin.com

’

(search for ‘F5U208’). Unpack the drivers (by default the folder ‘C:\F5U208\’

is created). This is the path which you have to specify during the installation.

Connect the Belkin video adapter to a free USB port. The Windows ‘Found

New Hardware Wizard’ will start automatically.

Follow the instructions presented during the installation process (e.g. specify

the location of the unpacked drivers, default name: C:\F5U208).

Note: During installation the Windows® Logo testing may display a compatibility

warning. Choose ‘Continue anyway’ to continue with the installation.

The Windows ‘Found New Hardware Wizard’ must be completed twice

during the installation procedure, once for video and once for audio signal.

Connect the Probot camera and view the video signal (Section E.2.1).

E.2.1

Connecting the Camera and Displaying the Video Signal

After installation of the Belkin VideoBusII connect the Probot to the video

adapter. Use the BNC-to-video adapter and the BNC cable as presented in

FIGURE E-1.

Summary of Contents for Probot 161403























































































































Search results

Summary of Contents for Probot 161403

Reviews:

Related manuals for Probot 161403

Brands by name

Popular brands

LC Packings Probot 161403, User Manual

Search results

Summary of Contents for Probot 161403

Reviews:

Related manuals for Probot 161403

Brands by name

Popular brands