lb pa Series Operation Manual Download Page 3

3

Important Safety Informations

Components inside the device may generate high voltages which can lead to life-threatening electric
shocks if touched.

CAUTION!

Service and repair work must only be carried out by qualified personnel. Do not open the case as
there is a risk of electric shock. There are no controls or components inside the device that require
you to open the case. If the case has to be opened by qualified personnel, make sure that the device
is completely disconnected from the power supply.

Use the power cable provided to connect the device to the mains . If a cable is damaged, do not try to
repair it. The device must be grounded. Never isolate the grounding on the mains plug.

The mains fuse is located inside the device. The mains fuse sho uld only be replaced with a fuse of the
same rating. Never bypass the main fuse or replace it with a higher rating.

The operating voltage must match the local power supply.

The device should be shielded from moisture and wet conditions. It must not be operated in rain or close
to water, baths, washbasins, sinks, swimming pools or in damp environments. Do not place any objects
filled with water such as vases, glasses or bottles on the device.

Avoid direct sunlight and do not install it in the direct vicinity of radiators or other heat sources.
Upon sudden change of climatic conditions (e. g. transfer from a cold place to a warm room) water may
condense inside the device, which may lead to malfunction or damage. Before switch-on wait until the
amplifiers have reached room temperature.

Unplug the mains plug to protect the device during a thunderstorm or if it is going to be left unsupervised 
or unused for a longer period of time. This prevents the device being damaged by lightning strikes or 
voltage surges in the mains grid. Do not touch the case when the device is in use as it may heat up
during operation. Make sure that the device is ventilated sufficiently.

Improper use will invalidate the warranty!

Disclaimer
lb is not liable for damage to speakers or other equipment caused by negligence or in cases where
the product has been used for something other than its intended purpose. In particular, lb is not liable
for lost earnings or other financial losses incurred by the purchaser. This limitation also applies to the
personal liability of employees, representatives and agents.

These products meet the requirements of European Directive 2002/96/EC (WEEE), 2002/95/EC (RoHS) and 
EurAsian Conformity EAC TR CU 010/2011. 

THIS UNIT MUST

BE EARTHED!

Fuse 0,5 A

slow

THIS UNIT MUST

BE EARTHED!

Fuse 0,5 A

slow

THIS UNIT MUST

BE EARTHED!

Fuse 0,5 A

slow

THIS UNIT MUST

BE EARTHED!

Fuse 0,5 A

slow

Please read the following instructions carefully before installing or connecting the unit!

Summary of Contents for pa Series

















Reviews: