LAWO V_pro8 Installation & Operation Manual Download Page 42

Page: 42 / 109

V1.0/2

V_pro8 Manual

Operation (Web Browser Control)

Operating Principles

Menu Selection & Navigation

After

you are presented with the main menu bar.

As you move your mouse over the menus, the buttons enlarge to emphasise your intended selection:

Click to select a main menu option - for example,

SDI Out

The window updates and the main menu bar

expands

; one of the inner options is automatically

selected - e.g. SDI

Out 1

The operating window is now divided into two; the upper area displays information about the main
menu selection (SDI

Out 1

), while the lower area provides access to its parameters:

If you have signals connected, then you will see audio levels on any metering and live video
streaming. Note that video is only monitored for the SDI Out. Therefore, you will NOT see
video thumbnails or the video preview if you select the

SDI In

main menu.

The left hand side of the information area can display different options. Click on the green
button beside

PPM

to choose from

Timecode

Vectorscope

WFM

(WaveForm Monitor)

PPM Meter

. See

SDI Out: Display Options

Summary of Contents for V_pro8














































































































Search results

Summary of Contents for V_pro8

Reviews:

Related manuals for V_pro8

Brands by name

Popular brands

LAWO V_pro8, Installation & Operation Manual

Search results

Summary of Contents for V_pro8

Reviews:

Related manuals for V_pro8

Brands by name

Popular brands