LAWO V_pro8 Installation & Operation Manual Download Page 37

Page: 37 / 109

V_pro8 Manual

V1.0/2

Installation & Configuration
Reference Settings

Reference Settings

The video and audio reference signals for the

pro8

are selected from the

Reference Setting

options

in the

Timing

menu.

The system can be referenced to:

Analog Genlock High Definition Tri-Level Sync (SMPTE-274M/296M) - connected to the rear
panel's

REF IN

Standard Definition 1V Black & Burst (SMPTE-170M/318M) - connected to the rear panel's

REF IN

SDI - from any of the 8 digital

SDI inputs

Internal

In Version 1.0, the audio reference is ALWAYS set to

Follow Video

. This means that the

system is clocked from a single reference source. In a future software release, you will be
able to clock video and audio signals independently.

Summary of Contents for V_pro8














































































































Search results

Summary of Contents for V_pro8

Reviews:

Related manuals for V_pro8

Brands by name

Popular brands

LAWO V_pro8, Installation & Operation Manual

Search results

Summary of Contents for V_pro8

Reviews:

Related manuals for V_pro8

Brands by name

Popular brands